U-Boot 1.3.2 (Oct 24 2008 - 16:50:58) U-Boot code: 00000000 -> 0000e820 data: 00014088 -> 0001a778 SDRAM: 64 MB at address 0x10000000 Testing SDRAM...OK malloc: Using memory from 0x13fa5000 to 0x13fe5000 DMA: Using memory from 0x13fa1000 to 0x13fa5000 Flash: 8 MB at address 0x00000000 DRAM Configuration: Bank #0: 10000000 64 MB In: serial Out: serial Err: serial Net: macb0 Press SPACE to abort autoboot in 3 seconds macb0: Starting autonegotiation... macb0: Autonegotiation complete macb0: link up, 100Mbps full-duplex (lpa: 0xc5e1) Using macb0 device File transfer via NFS from server 192.168.1.105; our IP address is 192.168.1.8 Filename '/srv/icnova/boot/uImage'. Load address: 0x10400000 Loading: *\0x08################################################################# \0x09 ################################################################# \0x09 ################################################################# \0x09 ################################################################# \0x09 ################# done Bytes transferred = 1413489 (159171 hex) ## Booting image at 10400000 ... Image Name: Linux-2.6.28.4 Image Type: AVR32 Linux Kernel Image (gzip compressed) Data Size: 1413425 Bytes = 1.3 MB Load Address: 10000000 Entry Point: 90000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel at 90000000 (params at 13fa5008)... Linux version 2.6.28.4 (root@freya) (gcc version 4.2.2-atmel.1.1.3.avr32linux.1) #1 Sun Oct 4 15:14:25 CEST 2009 CPU: AT32AP700x chip revision C CPU: AP7 [01] core revision 0 (AVR32B arch revision 1) CPU: MMU configuration: Shared TLB CPU: features: dsp simd ocd perfctr java CPU: Running at 140.000 MHz Physical memory: 10000000-13ffffff Reserved memory: 10000000-1019bfcf: Kernel code 1019bfd0-10259217: Kernel data Exception vectors start at 90014000 CPU: Paging enabled Node 0: start_pfn = 0x10000, low = 0x14000 Node 0: mem_map starts at 9025c000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: nfsroot=192.168.1.105:/srv/icnova/ ip=192.168.1.8:192.168.1.105::255.255.255.0::eth0:none PID hash table entries: 256 (order: 8, 1024 bytes) avr32_comparator: irq 0, 140.000 MHz Console: colour dummy device 80x25 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 62492k/62556k available (1567k kernel code, 2980k reserved, 144k data, 80k init) Calibrating delay using timer specific routine.. 282.83 BogoMIPS (lpj=470142) Mount-cache hash table entries: 512 net_namespace: 716 bytes smc smc.0: Atmel Static Memory Controller at 0xfff03400 NET: Registered protocol family 16 pdc pdc.0: Atmel Peripheral DMA Controller enabled at32_eic at32_eic.0: External Interrupt Controller at 0xfff00100, IRQ 19 at32_eic at32_eic.0: Handling 4 external IRQs, starting with IRQ 64 AVR32 AP Power Management enabled bio: create slab at 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 audit: initializing netlink socket (disabled) type=2000 audit(1167609600.370:1): initialized JFFS2 version 2.2. (NAND) \0xc2\0xa9 2001-2006 Red Hat, Inc. msgmni has been set to 122 alg: hash: Chunking test 1 failed for md5-generic 00000000: 24 e5 f6 e1 36 2e 67 bb a6 f6 2f 5f 81 ff bb a4 alg: No test for stdrng (krng) io scheduler noop registered io scheduler cfq registered (default) atmel_lcdfb atmel_lcdfb.0: 225KiB frame buffer at 13980000 (mapped at b3980000) Console: switching to colour frame buffer device 40x30 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0xff000000 (mapped at ff000000), irq 1 atmel_usart.0: ttyS0 at MMIO 0xffe00c00 (irq = 6) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xffe01000 (irq = 7) is a ATMEL_SERIAL atmel_usart.2: ttyS2 at MMIO 0xffe01400 (irq = 8) is a ATMEL_SERIAL atmel_usart.3: ttyS3 at MMIO 0xffe01800 (irq = 9) is a ATMEL_SERIAL eth0 (macb): not using net_device_ops yet MACB_mii_bus: probed eth0: Atmel MACB at 0xfff01800 irq 25 (00:1f:e5:00:0a:87) eth0: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=0:00, irq=67) physmap platform flash device: 00800000 at 00000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0041 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Using physmap partition information Creating 3 MTD partitions on "physmap-flash.0": 0x00000000-0x00020000 : "u-boot" 0x00020000-0x00030000 : "env" 0x00030000-0x00800000 : "root" ------------[ cut here ]------------ WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x1c/0x2c() sysfs: duplicate filename 'physmap-flash.0' can not be created Modules linked in: Call trace: [<9001e7a6>] warn_slowpath+0x42/0x54 [<900cfddc>] vsnprintf+0x25c/0x5de [<900cfddc>] vsnprintf+0x25c/0x5de [<9001cac6>] scheduler_tick+0x5a/0x60 [<9002bb00>] ktime_divns+0x4c/0x70 [<900cc4c0>] ida_get_new_above+0x1c/0x10c [<90059ad8>] ifind+0x8/0x3c [<90075aa6>] sysfs_ilookup_test+0x0/0xa [<9000030c>] kernel_init+0x0/0x90 [<90059b2a>] ilookup5+0x1e/0x24 [<90075f80>] sysfs_add_one+0x1c/0x2c [<9000030c>] kernel_init+0x0/0x90 [<900763ea>] create_dir+0x32/0x5c [<90076436>] sysfs_create_dir+0x22/0x30 [<9000940c>] physmap_init+0x0/0x20 [<9000030c>] kernel_init+0x0/0x90 [<900ccc78>] kobject_add_internal+0x90/0x140 [<900ccc86>] kobject_add_internal+0x9e/0x140 [<9000940c>] physmap_init+0x0/0x20 [<900ccdbc>] kobject_add_varg+0x20/0x2c [<9000940c>] physmap_init+0x0/0x20 [<9000030c>] kernel_init+0x0/0x90 [<900cce1c>] kobject_add+0x30/0x3c [<9000940c>] physmap_init+0x0/0x20 [<900f92e4>] device_add+0x64/0x38c [<900cc982>] kobject_init_internal+0xe/0x30 [<9001f04c>] printk+0xc/0x10 [<900fb9c0>] platform_device_add+0xc0/0x110 [<9000940c>] physmap_init+0x0/0x20 [<9000030c>] kernel_init+0x0/0x90 [<900fba5a>] platform_device_register+0xe/0x10 [<9000940c>] physmap_init+0x0/0x20 [<90009424>] physmap_init+0x18/0x20 [<9000940c>] physmap_init+0x0/0x20 [<900152f2>] do_one_initcall+0x32/0x104 [<90013d98>] __early_initcall_end+0x2a4/0x334 [<90013af4>] __early_initcall_end+0x0/0x334 [<9000940c>] physmap_init+0x0/0x20 [<900394f8>] register_irq_proc+0x48/0x6c [<90039542>] init_irq_proc+0x26/0x48 [<90000352>] kernel_init+0x46/0x90 [<90013d98>] __early_initcall_end+0x2a4/0x334 [<90013af4>] __early_initcall_end+0x0/0x334 [<90020a14>] do_exit+0x0/0x460 [<9000030c>] kernel_init+0x0/0x90 [<90020a14>] do_exit+0x0/0x460 ---[ end trace 3229c192e1fe8551 ]--- kobject_add_internal failed for physmap-flash.0 with -EEXIST, don't try to register things with the same name in the same directory. Call trace: [<900cd0ac>] kobject_rename+0xdc/0x11c [<900ccce4>] kobject_add_internal+0xfc/0x140 [<900ccdbc>] kobject_add_varg+0x20/0x2c [<9000940c>] physmap_init+0x0/0x20 [<9000030c>] kernel_init+0x0/0x90 [<900cce1c>] kobject_add+0x30/0x3c [<9000940c>] physmap_init+0x0/0x20 [<900f92e4>] device_add+0x64/0x38c [<900cc982>] kobject_init_internal+0xe/0x30 [<9001f04c>] printk+0xc/0x10 [<900fb9c0>] platform_device_add+0xc0/0x110 [<9000940c>] physmap_init+0x0/0x20 [<9000030c>] kernel_init+0x0/0x90 [<900fba5a>] platform_device_register+0xe/0x10 [<9000940c>] physmap_init+0x0/0x20 [<90009424>] physmap_init+0x18/0x20 [<9000940c>] physmap_init+0x0/0x20 [<900152f2>] do_one_initcall+0x32/0x104 [<90013d98>] __early_initcall_end+0x2a4/0x334 [<90013af4>] __early_initcall_end+0x0/0x334 [<9000940c>] physmap_init+0x0/0x20 [<900394f8>] register_irq_proc+0x48/0x6c [<90039542>] init_irq_proc+0x26/0x48 [<90000352>] kernel_init+0x46/0x90 [<90013d98>] __early_initcall_end+0x2a4/0x334 [<90013af4>] __early_initcall_end+0x0/0x334 [<90020a14>] do_exit+0x0/0x460 [<9000030c>] kernel_init+0x0/0x90 [<90020a14>] do_exit+0x0/0x460 atmel_spi atmel_spi.0: Atmel SPI Controller at 0xffe00000 (irq 3) ads7846 spi0.2: touchscreen, irq 144 input: ADS784x Touchscreen as /class/input/input0 i2c-gpio i2c-gpio.0: using pins 6 (SDA) and 7 (SCL) at32_wdt at32_wdt.0: AT32AP700X WDT at 0xfff000b0, timeout 2 sec (nowayout=0) dw_dmac.0: DesignWare DMA Controller, 3 channels TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. cpufreq: AT32AP CPU frequency driver atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff02400 irq 28, 1 slots mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new SD card at address 0002 mmcblk0: mmc0:0002 00000 974 MiB mmcblk0: p1 IP-Config: Complete: device=eth0, addr=192.168.1.8, mask=255.255.255.0, gw=255.255.255.255, host=192.168.1.8, domain=, nis-domain=(none), bootserver=192.168.1.105, rootserver=192.168.1.105, rootpath= Looking up port of RPC 100003/2 on 192.168.1.105 eth0: link up (100/Full) Looking up port of RPC 100005/1 on 192.168.1.105 VFS: Mounted root (nfs filesystem) on device 0:12. Freeing init memory: 80K (90000000 - 90014000)