Starting kernel at 90000000 (params at 13fa5008)...

Linux version 2.6.24-icnova_base1 (claude@Extensa) (gcc version 4.0.4-atmel.0.99.0) #17 Sat Mar 22 19:53:52 CET 2008
CPU: AT32AP700x chip revision C
CPU: AP7 [01] core revision 0 (AVR32B arch revision 1)
CPU: MMU configuration: Shared TLB
CPU: features: dsp simd ocd perfctr java
CPU: Running at 140.000 MHz
Physical memory:
  10000000-13ffffff
Reserved memory:
  10000000-101a9765: Kernel code
  101a9766-10251317: Kernel data
Exception vectors start at 90014000
CPU: Paging enabled
Node 0: start_pfn = 0x10000, low = 0x14000
Node 0: mem_map starts at 90254000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0 root=1F02 rootfstype=jffs2 mtdparts=physmap-flash.0:128k(boot)ro,64k(env)ro,-(root)
PID hash table entries: 256 (order: 8, 1024 bytes)
timer: AT32AP system timer/counter at 0xfff00c00 irq 22
Console: colour dummy device 80x25
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62524k/62588k available (1621k kernel code, 2948k reserved, 124k data, 80k init)
Calibrating delay using timer specific routine.. 280.40 BogoMIPS (lpj=560813)
Mount-cache hash table entries: 512
net_namespace: 156 bytes
NET: Registered protocol family 16
ICNova: 6 Leds
pio0: pin 23 is busy
Call trace:
 [<90001114>] at32_select_periph+0x5c/0xac
 [<90001c36>] at32_add_device_ssc+0xd2/0x1c8
 [<90013634>] __initcall_icnova_init2+0x0/0x4
 [<90002480>] icnova_init+0xc4/0xec
 [<900005d2>] kernel_init+0x56/0x1b8
 [<90014162>] ret_from_fork+0x4/0x14
 [<9001818c>] kernel_thread_helper+0x0/0x6
 [<9001818c>] kernel_thread_helper+0x0/0x6
 [<90021264>] do_exit+0x0/0x530
 [<90021264>] do_exit+0x0/0x530
 [<9000057c>] kernel_init+0x0/0x1b8

pdc pdc.0: Atmel Peripheral DMA Controller enabled
at32_eic at32_eic.0: External Interrupt Controller at 0xfff00100, IRQ 19
at32_eic at32_eic.0: Handling 4 external IRQs, starting with IRQ 64
smc smc.0: Atmel Static Memory Controller at 0xfff03400
cpufreq: AT32AP CPU frequency driver
dmac0: DesignWare DMA controller at 0xff200000 irq 2
Time: avr32 clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1167609600.362:1): initialized
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler cfq registered (default)
atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 13d00000 (mapped at b3d00000)
Console: switching to colour frame buffer device 30x40
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0xff000000 (mapped at ff000000), irq 1
atmel_usart.0: ttyS0 at MMIO 0xffe00c00 (irq = 6) is a ATMEL_SERIAL
ssc ssc.0: Atmel SSC device at 0xffe01c00 (irq 10)
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfff01800 irq 25 (00:1f:e5:00:00:5a)
eth0: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=0:00, irq=-1)
physmap platform flash device: 00800000 at 00000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0041
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
mtd: scanning for physmap-flash.0
3 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 3 MTD partitions on "physmap-flash.0":
0x00000000-0x00020000 : "boot"
ftl_cs: FTL header not found.
0x00020000-0x00030000 : "env"
ftl_cs: FTL header not found.
0x00030000-0x00800000 : "root"
ftl_cs: FTL header not found.
block2mtd: version $Revision: 1.30 $
atmel_usba_udc atmel_usba_udc.0: MMIO registers at 0xfff03000 mapped at fff03000
atmel_usba_udc atmel_usba_udc.0: FIFO at 0xff300000 mapped at ff300000
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using atmel_usba_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep3in-int
usb0: MAC 66:68:d9:3e:40:05
usb0: HOST MAC 56:21:1a:61:94:57
usb0: RNDIS ready
i2c /dev entries driver
atmel_twi atmel_twi.0: Atmel TWI/I2C adapter (baudrate 100k) at 0xffe00800.
i2c-adapter i2c-0: SMBus Quick command not supported, can't probe for chips
mmc_host mmc0: Atmel MCI controller at 0xfff02400 irq 28
Registered led device: pwrled:red
Registered led device: led1:green
Registered led device: led5:green
Registered led device: led6:green
Registered led device: led7:green
Registered led device: led8:green
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC).
ALSA device list:
  #0: Dummy 1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 80K (90000000 - 90014000)
init started: BusyBox v1.5.0 (2008-02-24 16:17:13 CET) multi-call binary
eth0: link up (100/Full)
starting pid 846, tty '/dev/ttyS0': '/sbin/getty'
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 849) exited. Scheduling it for restart.



Thank you for using In-Circuit ICNova

Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 871) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 892) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 913) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 934) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 955) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 976) exited. Scheduling it for restart.
Can't open /dev/ttygserial: No such device or address
process '/sbin/getty -L ttygserial 115200 vt100' (pid 997) exited. Scheduling it for restart.