smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: Hitachi HDT725025VLA380 Serial Number: VFL101R60UU6AF Firmware Version: V5DOA7EA User Capacity: 250.059.350.016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1 Local Time is: Wed Aug 6 16:11:18 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (4949) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 83) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 118 118 024 Pre-fail Always - 322 (Average 311) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 212 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 290 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 198 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 212 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 212 194 Temperature_Celsius 0x0002 193 193 000 Old_age Always - 31 (Lifetime Min/Max 10/56) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 1097 SMART Error Log Version: 1 ATA Error Count: 93 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 93 occurred at disk power-on lifetime: 283 hours (11 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 10 01 ea 7f Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fe a2 01 10 01 0a e0 00 00:32:06.900 [VENDOR SPECIFIC] fe a1 00 00 00 00 a0 00 00:32:06.900 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:32:06.700 [VENDOR SPECIFIC] c1 00 00 00 00 00 00 00 00:32:06.700 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:32:06.600 [VENDOR SPECIFIC] Error 92 occurred at disk power-on lifetime: 283 hours (11 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 10 01 ea 7f Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fe a2 01 10 01 0a e0 00 00:29:03.300 [VENDOR SPECIFIC] fe a1 00 00 00 00 a0 00 00:29:03.300 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:29:03.200 [VENDOR SPECIFIC] c1 00 00 00 00 00 00 00 00:29:03.200 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:29:03.000 [VENDOR SPECIFIC] Error 91 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 10 01 ea 7f Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fe a2 01 10 01 0a e0 00 00:02:45.700 [VENDOR SPECIFIC] fe a1 00 00 00 00 a0 00 00:02:45.700 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:02:45.600 [VENDOR SPECIFIC] c1 00 00 00 00 00 00 00 00:02:45.600 [VENDOR SPECIFIC] fe a6 50 60 00 00 00 00 00:02:45.500 [VENDOR SPECIFIC] Error 90 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c2 00 00 00 00 00 00 00 00:02:46.400 [VENDOR SPECIFIC] ec 00 00 00 00 00 a0 00 00:02:46.400 IDENTIFY DEVICE 25 20 00 00 00 00 e0 04 00:02:46.400 READ DMA EXT 25 20 01 00 00 00 e0 08 00:02:07.800 READ DMA EXT 25 20 01 00 00 00 e0 08 00:02:07.800 READ DMA EXT Error 89 occurred at disk power-on lifetime: 274 hours (11 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 51 00 00 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c2 00 00 00 00 00 00 00 00:02:46.400 [VENDOR SPECIFIC] ec 00 00 00 00 00 a0 00 00:02:46.400 IDENTIFY DEVICE 25 20 00 00 00 00 e0 04 00:02:46.400 READ DMA EXT 25 20 01 00 00 00 e0 08 00:02:07.800 READ DMA EXT 25 20 01 00 00 00 e0 08 00:02:07.800 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 285 - # 2 Short offline Completed without error 00% 261 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.