RomBOOT > U-Boot 1.1.5 (Jun 20 2009 - 00:34:40) DRAM: 32 MB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 ( NAND 64MiB 3,3V 8-bit) NAND: Pagesize: 512, Blocksize: 16K, OOBsize: 16 64 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial PHY not reset!! Hit any key to stop autoboot: 0 NAND read: device 0 offset 1048576, size 2200000 ... 2200000 bytes read: OK ## Booting image at 20a00000 ... Image Name: linux-2.6 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1359068 Bytes = 1.3 MB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................. ........................... done, booting the kernel. Linux version 2.6.27 (snoopy@snoopy-desktop) (gcc version 4.2.0 20070413 (prerel ease) (CodeSourcery Sourcery G++ Lite 2007q1-10)) #232 Sat Jun 20 00:39:27 CEST 2009 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00057177 Machine: Atmel AT91SAM9260-EK Memory policy: ECC disabled, Data cache writethrough Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: mem=32M console=ttyS0,115200 console=tty0 root=/dev/mmcblk0 p1 rw init=linuxrc rootdelay=1 AT91: 96 gpio irqs in 3 banks PID hash table entries: 128 (order: 7, 512 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 32MB = 32MB total Memory: 29624KB available (2508K code, 198K data, 104K init) Calibrating delay loop... 98.91 BogoMIPS (lpj=494592) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NetWinder Floating Point Emulator V0.97 (double precision) NTFS driver 2.1.29 [Flags: R/W]. JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. fuse init (API version 7.9) msgmni has been set to 57 io scheduler noop registered io scheduler anticipatory registered (default) ls020 spi fb driver atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL brd: module loaded loop: module loaded Linux video capture interface: v2.00 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods SCSI Media Changer driver v0.25 Driver 'ch' needs updating - please use bus_type methods Generic platform RAM MTD, (c) 2004 Simtec Electronics atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffcc000 (irq 13) Console: switching to colour frame buffer device 29x22 fb0: ls020 frame buffer device, 21d70000 base address 45K of video memory usbmon: debugfs is not available at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 20, io mem 0x00500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. udc: at91_udc version 3 May 2006 zero gadget: Gadget Zero, version: Cinco de Mayo 2008 zero gadget: zero ready mice: PS/2 mouse device common for all mice i2c /dev entries driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Waiting 1sec before mounting root device... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new SD card at address ba1a mmcblk0: mmc0:ba1a SD064 60928KiB mmcblk0: p1 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on mmcblk0p1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing init memory: 104K Populating /dev using udev: /etc/init.d/S10udev: line 79: can't create /proc/sys /kernel/hotplug: nonexistent directory cannot open /dev/null error initializing udevd socket FAIL done Starting portmap: done Initializing random number generator... done. Starting network... ip: socket: Function not implemented ip: socket: Function not implemented ifup: can't open '/var/run/ifstate': No such file or directory Welcome to the Erik's uClibc development environment. AT91SAM9 login: