smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3160023AS Serial Number: 5MT1HCM6 Firmware Version: 8.12 User Capacity: 160.000.000.000 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Sun Jun 13 10:10:21 2010 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 94) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 058 049 006 Pre-fail Always - 173568590 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2488 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 21 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 254028039 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 8438 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2489 194 Temperature_Celsius 0x0022 043 047 000 Old_age Always - 43 (0 9 0 0) 195 Hardware_ECC_Recovered 0x001a 058 049 000 Old_age Always - 173568590 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 3 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 occurred at disk power-on lifetime: 6782 hours (282 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 63 99 17 e0 Error: IDNF at LBA = 0x00179963 = 1546595 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d8 00 3f 98 17 e0 00 00:09:54.777 READ VERIFY SECTOR(S) EXT 42 d8 00 3f 96 17 e0 00 00:09:54.773 READ VERIFY SECTOR(S) EXT 42 d8 00 3f 94 17 e0 00 00:09:54.768 READ VERIFY SECTOR(S) EXT 42 d8 00 3f 92 17 e0 00 00:09:54.764 READ VERIFY SECTOR(S) EXT 42 d8 00 3f 90 17 e0 00 00:09:54.759 READ VERIFY SECTOR(S) EXT Error 2 occurred at disk power-on lifetime: 71 hours (2 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 87 b8 9a 17 e2 Error: IDNF at LBA = 0x02179ab8 = 35101368 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 00 3f 9a 17 e2 00 01:28:47.986 READ VERIFY SECTOR(S) 40 00 00 3f 99 17 e2 00 01:28:47.983 READ VERIFY SECTOR(S) 40 00 00 3f 98 17 e2 00 01:28:48.298 READ VERIFY SECTOR(S) 40 00 00 3f 97 17 e2 00 01:28:48.296 READ VERIFY SECTOR(S) 40 00 00 3f 96 17 e2 00 01:28:48.285 READ VERIFY SECTOR(S) Error 1 occurred at disk power-on lifetime: 70 hours (2 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 67 d8 9a 17 e2 Error: IDNF at LBA = 0x02179ad8 = 35101400 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 00 3f 9a 17 e2 00 00:15:37.127 READ VERIFY SECTOR(S) 40 00 00 3f 99 17 e2 00 00:15:37.125 READ VERIFY SECTOR(S) 40 00 00 3f 98 17 e2 00 00:15:37.123 READ VERIFY SECTOR(S) 40 00 00 3f 97 17 e2 00 00:15:37.120 READ VERIFY SECTOR(S) 40 00 00 3f 96 17 e2 00 00:15:37.118 READ VERIFY SECTOR(S) SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short captive Completed without error 00% 7086 - # 2 Short captive Completed without error 00% 2089 - # 3 Short captive Completed without error 00% 1691 - # 4 Short captive Completed without error 00% 927 - # 5 Short offline Completed without error 00% 2 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.