Im Forum und im Wiki
-
Thread
Unsauberer Pegel nach TXB0104PWR
the output drivers of the TXB0104 device. For the same reason, the TXB0104 device must not be used in applications such as I 2C or 1-Wire where an open-drain driver is connected on the bidirectional data I/O. For these applications
Hallo Frank, ich hatte noch TXB0104PWR rumliegen von einem anderen Projekt und hatte gehofft die einfach nutzen zu können, wenn ich jetzt sowieso eine neue Revision mache klingen die 74LVC1T45 natürlich sinnvoller, gerade weil ich nur
-
Thread
Ich will eine SD Karte nutzen. Bekomme Levelshifter nicht auf Board. [Eagle 5.0]
Spannungsregler für die SD Karte. Nun habe ich hier im Forum und bei AVR Freaks mehrmals den TXB0104 von TI als Koppelglied zur SD Karte gesehen. Leider bin ich zu blöd in Eagle 5.0 von der ich die Non Profit Lizenz besitze,ein Package und ein passendes Schaltbild zu erzeugen. Speziell harpert
welches??? Antwort: Im ersten Post: Nun habe ich hier im Forum und bei AVR Freaks mehrmals den TXB0104 von TI als Koppelglied zur SD Karte gesehen. Ich suche also das Package zum TXB0104DR (Also dem Package zu dem SMD Bauteil mit der Bezeichnung: TXB0104DR) Ein ratloser Neuling schrieb: >
-
Thread
USBasp Levelshift will nicht so wie ich.
interessant sein, denke ich: [pre]The TXB0104 is designed to drive capacitive loads of up to 70 pF. The output drivers of the TXB0104 have low dc drive strength. If pullup or pulldown resistors are connected externally to the data I/Os, their
must be kept higher than 50 kO to ensure that they do not contend with the output drivers of the TXB0104. For the same reason, the TXB0104 should not be used in applications such as I2C or 1-Wire where an open-drain driver is connected on the bidirectional data I/O. For these applications, use a
-
Thread
SD-Karte mit Levelshifter Problem
Hat jemand einen TXB0104 mit einer SD-Card am Laufen ? Wäre gut zu wissen, dass es überhaupt prinzipiell geht :-)
) zulässt. Datenblatt: "Input Driver Requirements Typical IIN vs VIN characteristics of the TXB0104 are shown in Figure 2. For proper operation, the device driving the data I/Os of the TXB0104 must have drive strength of at least ±2 mA."
-
Thread
TXB0104 an MMC
Moin Moin, Nach langem Nerven mit dem TXB0104 und MMC Karten habe ich nun eine Lösung gefunden das Teil vernünftig zu betreiben. Das Problem ist, dass nach einem Kartenwechsel der TXB0104 den SPI Bus tot gelegt hat. Erst ein LOW an OE vom TXB0104
. Ich bin so gar nicht glücklich mit dieser Lösung, zumal im Netz diverse Schaltbeispiele mit TXB0104 und MMC ohne irgendwelche externe Beschaltung abgebildet sind. Bei mir funktionierte das aber nicht. Ein Pull-Up an DO der MMC damit ~2mA fließen half auch nichts. Vielleicht hilft es jemanden
-
Thread
Frage zu MachXOLF an TXB0104
angewiesen das ich die I/O Richtung wechseln kann. Am besten automatisch, weswegen ich mich für den TXB0104 als Pegelwandler entschieden habe. Über die interne Beschaltung der I/O Ports des anderen IC's habe ich leider keine weiteren Informationen. Zu Anfang hatte ich den I/O Wandler einfach verbunden
Bild mit (von Oben nach Unten): - 5V Ausgangssignal vom externen IC - Signal zwischen FPGA und TXB0104 ohne Pull Up/Down - Signal zwischen FPGA und TXB0104 mit internem Pull Down - Signal zwischen FPGA und TXB0104 mit internem Pull Up
-
Thread
Suche Treiber/Levelshifter 2V --> 5V
Bei den TXB muss man ein wenig aufpassen was man damit vorhat: The TXB0104 is designed to drive capacitive loads of up to 70 pF. The output drivers of the TXB0104 have low dc drive strength. If pullup or pulldown resistors are connected externally to the data I/Os, their
must be kept higher than 50 k Ω to ensure that they do not contend with the output drivers of the TXB0104. For the same reason, the TXB0104 should not be used in applications such as I 2 C or 1-Wire where an open- drain driver is connected on the bidirectional data I/O. For these applications, use a device