-
Datei
Lambdacontroller_ai_claude_2.ino
, 13.03, 13.06, 13.10, 13.14, 13.18, 13.21, 13.25, 13.29, 13.33, 13.36, 13.40, 13.44, 13.48, 13.51, 13.55, 13.59, 13.63, 13.67, 13.70, 13.74, 13.78, 13.82, 13.85, 13.89, 13.93, 13.96, 14.00, 14.04, 14.08, 14.11, 14.15, 14.19, 14.23, 14.26, 14.30, 14.34, 14.38, 14.41, 14.45, 14.49, 14.52, 14.56, 14.60
in „Bosch CJ125 mit AVR AT90CAN64“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
Lambdacontroller_ai_claude.txt
, 13.03, 13.06, 13.10, 13.14, 13.18, 13.21, 13.25, 13.29, 13.33, 13.36, 13.40, 13.44, 13.48, 13.51, 13.55, 13.59, 13.63, 13.67, 13.70, 13.74, 13.78, 13.82, 13.85, 13.89, 13.93, 13.96, 14.00, 14.04, 14.08, 14.11, 14.15, 14.19, 14.23, 14.26, 14.30, 14.34, 14.38, 14.41, 14.45, 14.49, 14.52, 14.56, 14.60
in „Bosch CJ125 mit AVR AT90CAN64“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
SRD.PDF
R9933789 10A/240VAC 28VDC 5. DIMENSION DRILLING WIRING DIAGRAM (unit:mm) (unit:mm) 1 6. COIL DATA CHART (AT20 C) ▯ Coil Nominal Nominal Coil Power Pull-In Drop-Out Max-Allowable Coil Voltage Voltage Current Resistance Consumption Voltage Voltage Voltage Sensitivity Code (VDC) (mA) (W –10% (W) (VDC) (VDC) (
in „ESP8266 D1 Mini + Relaismodul: Relais bleibt bei D1 dauerhaft eingeschaltet“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Motorola_MC44353_MC44354_MC44355_1998.pdf
T 500 – – ns C su;sto Hold time for Stop Condition Thd;sto 500 – – ns C Acknowledge Propagation Delay Tack;low – – 300 ns C SDA Fall Time at 3.0 mA sink and 130 pF Load – – 50 ns C SDA Fall Time at 3.0 mA sink and
in „Pollin ist pleite :-(“ · Offtopic ·
-
Datei
dds-fast.asm
.db 0x53,0x52,0x52,0x52,0x51,0x51,0x51,0x51 .db 0x50,0x50,0x4f,0x4e,0x4d,0x4c,0x4a,0x48 .db 0x46,0x44,0x41,0x3e,0x3b,0x38,0x35,0x31 .db 0x2e,0x2b,0x27,0x24,0x21,0x1f,0x1c,0x1a .db 0x18,0x16,0x15,0x13,0x12,0x11,0x10,0x0f .db 0x0e
in „Claude Code trifft AVR-Assembler: vom Chip in den Browser mit einem Prompt“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
T6963C.pdf
The hardware interrupt occurs during the address calculation period (at the end of each line). If a MSB = 0 command is sent to the T6963C during this period, the T6963C enters Wait status. If a status check is not carried out in this state before the next command is sent
in „altes Phytec MCB-51 Monitor/Basic Befehle?“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
dds-orig.asm
,0x5c,0x5e .db 0x60,0x62,0x64,0x66,0x68,0x6a,0x6c,0x6e .db 0x70,0x72,0x74,0x76,0x78,0x7a,0x7c,0x7e .db 0x80,0x82,0x84,0x86,0x88,0x8a,0x8c,0x8e .db 0x90,0x92,0x94,0x96,0x98,0x9a,0x9c,0x9e .db 0xa0,0xa2,0xa4,0xa6,0xa8,0xaa
in „Claude Code trifft AVR-Assembler: vom Chip in den Browser mit einem Prompt“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
siplace-s27hm.pdf
main switch. . . . . . . . . . . . . . . . . . . . . . 50 2.7.1 Placement system switched off at the main power switch, but still connected . . . . . 51 2.7.2 Placement system switched off at the main power switch and disconnected . . . . . . 51 2.7.3 Compressed air conditions in the machine after
in „Siplace 80 Potentialverteiler“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Sartorius_Waage_Manual_Anleitung_Handbuch_QC7DCE-S.pdf
number entered manually without a decimal point is always a piece count! You can exit this application at any time by pressing c/c + u/w or g/W, and proceed with a new counting task. Input of Reference Weight “wRef” If you know the weight of a part, you can enter it directly as the reference weight “wRef
in „Frage zu einer Waage / Sartorius QC7DCE-S“ · Mechanik, Gehäuse, Werkzeug ·