Hier ist der console output:
C:\Programme\avrdude>avrdude -p t44 -c ponyser -C avrdude.conf -P com2
-n -v -U flash:w:"C:\home\mik
e\AVR_Project\Blinker\default\Blinker.hex":i
avrdude: Version 5.5, compiled on Nov 8 2007 at 16:08:45
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is "avrdude.conf"
Using Port : com2
Using Programmer : ponyser
AVR Part : ATtiny44
Chip Erase delay : 4500 us
PAGEL : P00
BS2 : P00
RESET disposition : possible i/o
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages
MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------
----- ----- ---------
eeprom 65 6 4 0 no 256 4 0
4000 4500 0xff 0xff
flash 65 6 32 0 yes 4096 64 64
4500 4500 0xff 0xff
signature 0 0 0 0 no 3 0 0
0 0 0x00 0x00
lock 0 0 0 0 no 1 0 0
9000 9000 0x00 0x00
lfuse 0 0 0 0 no 1 0 0
9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0
9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0
9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0
0 0 0x00 0x00
Programmer Type : SERBB
Description : design ponyprog serial, reset=!txd sck=rts
mosi=dtr miso=cts
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100%
0.01s
avrdude: Device signature = 0x1e9207
avrdude: safemode: lfuse reads as 62
avrdude: safemode: hfuse reads as DF
avrdude: safemode: efuse reads as FF
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be
performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file
"C:\home\mike\AVR_Project\Blinker\default\Blinker.hex"
avrdude: writing flash (126 bytes):
:2000000010C02AC029C028C027C026C025C024C023C022C021C020C01FC01EC01DC01CC
0C3
:200020001BC011241FBECFE5D1E0DEBFCDBF10E0A0E6B0E0EEE7F0E002C005900D92A03
6CE
:20004000B107D9F710E0A0E6B0E001C01D92A036B107E1F702D012C0D3CFCF93DF93CDB
79E
:1E006000DEB7E7E3F0E081E08083A8E3B0E0E8E3F0E0908181E089278C93F7CFFFCF64
:00000001FF
avrdude: 126 bytes of flash written
avrdude: verifying flash memory against
C:\home\mike\AVR_Project\Blinker\default\Blinker.hex:
avrdude: load data flash data from input file
C:\home\mike\AVR_Project\Blinker\default\Blinker.hex:
avrdude: input file C:\home\mike\AVR_Project\Blinker\default\Blinker.hex
contains 126 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100%
0.60s
avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0000
0x10 != 0xff
avrdude: verification error; content mismatch
avrdude: safemode: lfuse reads as 62
avrdude: safemode: hfuse reads as DF
avrdude: safemode: efuse reads as FF
avrdude: safemode: Fuses OK
avrdude done. Thank you.
Ich hoffe dies hilft weiter....
Gruss mike
