/* ESP32 BMP280 sender with DEEP SLEEP (3 seconds) BMP280 and BME280 sensor can be used: Enable it with the #define in the code You have also to adapt the receiver MAC in the code. external libraries: Temperature and
/* ESP32 BMP280 sender with DEEP SLEEP (3 seconds) BMP280 and BME280 sensor can be used: Enable it with the #define in the code You have also to adapt the receiver MAC in the code. external libraries: Temperature and
''' ESP32 sender for BME280 Communication Method: ESPNOW external library ttps://github.com/robert-hh/BME280 2026-01-26 mchris ''' peer = b'\xcc\x7b\x5c\x1e\xac\x5c' # MAC address of receiver ESP32 import network import espnow from machine import Pin, I2C import time import struct from bme280_float import * import re i2c = I2C(1, scl=Pin(22), sda=Pin(21), freq=100000) bme280 = BME280(i2c=i2c) led = Pin(2, Pin.OUT) # ESP32WROOM Pin2 led.on() # A WLAN interface must be active to send()/recv
MQTT
ESP-01
H3_Garage_Temp
DS18B20 Temperature 15.1 °C
BME280 Temperature 16.0 °C
BME280 Humidity 77.4 %
BME280 Dew point 12.0 °C
BME280 Pressure 1023.4 hPa
Configuration
Information
Firmware Upgrade
Console
Restart
Tasmota 15.0.1 (release-sensors) by Theo Arends
Sensitive Layer Over a 0.35 µm CMOS Array • Image Zone: 0.4 x 14 mm = 0.02" x 0.55" • Image Array: 8 x 280 = 2240 pixels • Pixel Pitch: 50 µm x 50 µm = 500 dpi • Pixel Clock: up to 2 MHz Enabling up to 1780 Frames per Second • Die Size: 1.64 x 17.46 mm • Operating Voltage: 3V to 3.6V • Naturally Protected
Sensitive Layer Over a 0.8 µm CMOS Array Image Zone: 0.4 x 14 mm = 0.02" x 0.55" Image Array: 8 x 280 = 2240 pixels Pixel Pitch: 50 µm x 50 µm = 500 dpi Pixel Clock: up to 2 MHz Enabling up to 1780 Frames per Second Die Size: 1.7 x 17.3 mm Operating Voltage: 3 V to 5.5 V Naturally Protected Against
PD 1.033A DPA Series Microelectronic ChipSwitch DIP Relay Power IC Relay 1.0 Amp Load Current, 20 - 280 VAC RMS General Description DPA Series Features The DPA Series ChipSwitch uses exclusive Interna- S X power IC chips n tional Rectifier S power integrated circuit technol- 25 Amp surge n ogy to form
Auto Restart Voltage 120 - 140 VAC per phase / 180 VAC per phase Acceptable Input Voltage Range 170 - 280 VAC per phase Maximum AC Input Current 40 A PV INPUT (DC) Maximum DC Voltage 900 VDC 900 VDC MPP Voltage Range 400 VDC ~ 800 VDC 350 VDC ~ 850 VDC NumberofMPPTrackers/MaximumInputCurrent 2 / 2 x 18.6A
/01-S/A CE I_n=0.1A I_n=40A I_delta=30mA 230/400V~ WENN KNOPF AUSGESPRUNGEN, ABLEITER ERSETZEN U_p=280V I_n=15xA VR7-280 ACHTUNG Wenn der rote Knopf herausgesprungen, hat der Ableiter angesprochen und ist sofort von Fachpersonal eines konzessionierten Elektrounternehmens auszutauschen. Hinweis gemäß
2mV
Ch1 Max 8mV
Ch1 Min -8mV
Edge Source
Ch1
Ch2
Ax1
Ax2
AC
AC Line
Ch1 100mV
Ch2 100mV
M 250µs
Ch2 280mV
Type <Edge>
Source Ch2
Coupling DC
Slope /
Level 280mV
Mode & Holdoff
00:01:09.080 --> 00:01:12.780] Inside we both know what's been going on [00:01:12.780 --> 00:01:17.280] We know the game and we're gonna play it [00:01:17.280 --> 00:01:21.380] And if you ask me how I'm feeling [00:01:21.380 --> 00:01:25.140] Don't tell me you're too blind to see [00:01:25.140 --> 00
00:01:09.120 --> 00:01:12.780] Inside we both know what's been going on [00:01:12.780 --> 00:01:17.280] We know the game and we're gonna play it [00:01:17.280 --> 00:01:21.380] And if you ask me how I'm feeling [00:01:21.380 --> 00:01:25.120] Don't tell me you're too blind to see [00:01:25.120 --> 00
is not limited the signal transmission, only depend on the speed of signal transmission. RESET time>280μs , it won't cause wrong reset while interruption, it supports the lower frequency and inexpensive MCU. Refresh Frequency updates to 2KHz, Low Frame Frequency and No Flicker appear in HD Video Camera
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
