-
Datei
timer.c
//H-Bruecke-1//CLR LPC_GPIO2->FIOCLR |=(1<<2); LPC_GPIO2->FIOCLR |=(1<<3); //H-Bruecke-2 LPC_GPIO2->FIOCLR |=(1<<4); LPC_GPIO2->FIOSET |=(1<<5); //H-Bruecke-3 LPC_GPIO0->FIOCLR |=(1<<2); LPC_GPIO0->FIOSET |=(1<<3); LPC_GPIO0
in „Problem mit Timer Interrupt LPC1769“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
emc.c
); //D0 LPC_SCU->SFSP1_8 = (MD_PLN_FAST | FUNC3); //D1 LPC_SCU->SFSP1_9 = (MD_PLN_FAST | FUNC3); //D2 LPC_SCU->SFSP1_10 = (MD_PLN_FAST | FUNC3); //D3 LPC_SCU->SFSP1_11 = (MD_PLN_FAST | FUNC3); //D4 LPC_SCU->SFSP1
in „LPC1857 ARM Cortex M3 Problem mit EMC und SDRAM“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
LPC407x_8x_177x_8x.h
define LPC_TIM2 ((LPC_TIM_TypeDef *) LPC_TIM2_BASE ) #define LPC_TIM3 ((LPC_TIM_TypeDef *) LPC_TIM3_BASE ) #define LPC_UART0 ((LPC_UART_TypeDef *) LPC_UART0_BASE ) #define LPC_UART1 ((LPC_UART1_TypeDef *) LPC_UART1
in „Einstieg LPC4088 QuickStart Board“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
can.c
; /* CAN2 is p2.7 and p2.8 LPC_PINCON->PINSEL4 |= 0x00014000;*/ LPC_CAN1->MOD = 1; /* Reset CAN */ LPC_CAN1->IER = 0; /* Disable Receive Interrupt */ LPC_CAN1->GSR = 0; /* Reset error counter when CANxMOD is in reset */ LPC_CAN1-
in „sprintf mehrfach“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
USB_Initialisierung.txt
LPC_PINCON->PINMODE3 = LPC_PINCON->PINMODE3 | 0x20000000; //Pull-Up und Pull-Down am Vbus PIN ausschalten //USB PIN[0]29/30 LPC_PINCON->PINSEL1 = LPC_PINCON->PINSEL1 | 0x14000000; //PIN 0.29 und 0.30 auf
in „LPC1769 USB einschalten“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
0005_lpc313x_ADC_PWM.patch
+ +config LPC313x_ADC + tristate "lpc313x ADC support" + help + Say Y to enable the ADC driver, when built as a module, the module will be called "lpc313x_adc". + +config LPC313x_PWM + tristate "lpc313x PWM support
in „GNUBLIN www.gnublin.org“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
0006_lpc313x_ADC_PWM.patch
+ +config LPC313x_ADC + tristate "lpc313x ADC support" + help + Say Y to enable the ADC driver, when built as a module, the module will be called "lpc313x_adc". + +config LPC313x_PWM + tristate "lpc313x PWM support
in „GNUBLIN www.gnublin.org“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
eeprom.c
uint8_t nvram_read(uint32_t address) { volatile uint32_t test; // I2C-Flags löschen LPC_I2C1->I2CONCLR = (1 << 5) | (1 << 4) | (1 << 3) | (1 << 2); // START ausgeben LPC_I2C1->I2CONSET = (1 << 5); // Auf Interrupt-Flag warten... while (!(LPC_I2C1->I2CONSET & (1 << 3))); test = LPC_I2C1
in „LPC1751 und 24LC01 per I2C“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
sct.c
(1<<0); //LPC_SCT->OUT[0].CLR = (1<<0); //LPC_SCT->RES = (3 << 0); LPC_SCT->OUT[0].SET = 0x00000003; LPC_SCT->OUT[0].CLR = 0x00000003; LPC_SCT->OUTPUT = (LPC_SCT->OUTPUT & ~0x00000001) | 0x00000000; /* Conflict resolution
in „LPC810 SCT-PWM Projekt Fehler“ · Mikrocontroller und Digitale Elektronik ·
-
Bild
LPCXpresso LP-S32K147 Development Board
LPCXpresso LP-S32K147, NXP, LPCXpresso.com/LP-S32K147, S32K147, NXP, LPCXpresso
in „[V] Diverses ICs, Entwicklungsbords, Raspberry Zubehör“ · Markt · · Platinenfotos
-
Datei
LPC11Axx.h
#define LPC_CT16B1 ((LPC_CT16B0_Type *) LPC_CT16B1_BASE) #define LPC_CT32B0 ((LPC_CT32B0_Type *) LPC_CT32B0_BASE) #define LPC_CT32B1 ((LPC_CT32B0_Type *) LPC_CT32B1_BASE) #define LPC_ADC ((LPC_ADC_Type *) LPC_ADC_BASE) #define LPC_DAC ((LPC_DAC_Type *) LPC_DAC_BASE) #define LPC_CMP ((LPC_CMP_Type *) LPC_CMP_BASE) #define LPC_FMC ((LPC_FMC_Type *) LPC_FMC_BASE) #define LPC_SSP0 ((LPC_SSP0_Type *) LPC_SSP0_BASE) #define LPC_IOCON
in „constexpr Mikrokontroller Pointer Hartwarezugriff“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
code.c
test = LPC_I2C1->I2STAT; if (test != 0x18) goto stop; // SW-Adresse ausgeben LPC_I2C1->I2DAT = address; // Flag löschen LPC_I2C1->I2CONCLR = (1 << 3); // Auf Interrupt-Flag warten... while (!(LPC_I2C1->I2CONSET & (1 << 3))); test = LPC_I2C1->I2STAT; if (test != 0x28) goto stop; // START ausgeben LPC_I2C1->I2CONSET = (1 << 5); // Flag löschen LPC_I2C1->I2CONCLR = (1 << 3) | (1 << 2); // Auf Interrupt-Flag warten... while (!(LPC_I2C1
in „LPC1751 und 24LC01 per I2C“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
usb_device.c
(uint32_t endpt, uint32_t psize) { LPC_USB->ReEp = (1UL << endpt); LPC_USB->EpInd = endpt; LPC_USB->MaxPSize = psize; LPC_USB->DevIntClr = EP_RLZED; while(!(LPC_USB->DevIntSt & EP_RLZED)); LPC_USB->DevIntClr = EP_RLZED; } uint8_t USB_SIE_ReadWrite
in „LPC1788 USB Device“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
i2c.c
PIO0_4; u=LPC_IOCON->PIO0_5; #ifdef LPC1769 LPC_PINCON->PINSEL1 |= (0x3 << 6); LPC_PINCON->PINSEL1 |= (0x3 << 8); LPC_PINCON->PINMODE1 &= ~(0x1 << 6); LPC_PINCON->PINMODE1 |= (0x1 << 7); LPC_PINCON->PINMODE1 &= ~
in „CAN UP - Aktor (LPC11Cxx)“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.txt
#include "LPC17xx.h" #include "GPIO_LPC17xx.h" #include "GPDMA_LPC17xx.h" #include "Global.h" #include <stdio.h> //*****************************************// // //*** Define fuer Eingabe von Binary // //********
in „LPC1769 USB einschalten“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
LinkerProblem.txt
" "./BUILD/LPC11U37H_401/GCC_ARM/SDFileSystem/FATFileSystem/FATFileSystem.o" "./BUILD/LPC11U37H_401/GCC_ARM/SDFileSystem/SDFileSystem.o" "./BUILD/LPC11U37H_401/GCC_ARM/src/main.o" "./mbed/fd96258d940d/TARGET_LPC11U37H
in „gcc Linker macht mich verrückt“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
Sourcecode.txt
void CLK_Einstellen{ LPC_SYSCON->SYSPLLCLKSEL =(1<<0); LPC_SYSCON->SYSPLLCLKUEN =(0<<0); LPC_SYSCON->SYSPLLCLKUEN =(1<<0); LPC_SYSCON->MAINCLKSEL =(1<<0); LPC_SYSCON->MAINCLKUEN =(0<<0); LPC_SYSCON->MAINCLKUEN =(1<<0); LPC_SYSCON
in „LPC1114/5 SPI/CLK Config“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
AN10864_1.pdf
” and “system_LPC17xx.h”. Re-name “LPC17xx.h” at root of demo to “LPC17xx_FreeRTOS_def.h” to avoid any conflict with “LPC17xx.h” in CMSIS CM3 core. “LPC17xx_FreeRTOS_def.h” expands some old macros that are used in some
in „FreeRTOS mit GCC aufm MB1760 (LPC1768)“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
usb_device.c
CMD_PHASE_CMD, CLEAR_BUFFER); return index; } void USB_RealizeEndpoint(uint32_t endpt, uint32_t psize) { LPC_USB->DevIntClr = EP_RLZED; LPC_USB->ReEp |= (1UL << endpt); LPC_USB->EpInd = endpt; LPC_USB->MaxPSize = psize; LPC_USB->DevIntClr = EP_RLZED; while(!(LPC_USB->DevIntSt & EP_RLZED)); LPC_USB->DevIntClr
in „LPC1788 USB Device“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
settings.xml
/> <lpc1768 file="target/lpc1768.cfg" /> <lpc1769 file="target/lpc1769.cfg" /> <lpc1788 file="target/lpc1788.cfg" /> <lpc17xx file="target/lpc17xx.cfg" /> <lpc1850 file="target/lpc1850.cfg" /> <lpc2103 file
in „STM32 - Code-Blocks + GCC + GDB“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
Externen Takt wählen LPC_SYSCON->SYSPLLCLKUEN =(0<<0); LPC_SYSCON->SYSPLLCLKUEN =(1<<0); LPC_SYSCON->MAINCLKSEL =(1<<0); //S28 Externer takt wird als Main CkL eingestellt LPC_SYSCON->MAINCLKUEN =(0<<0); //S29 This register
in „LPC1114/LPC111x SPI Config“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
lpc17xx_emac.c
@{ */ /* Includes ------------------------------------------------------------------- */ #include "lpc17xx_emac.h" #include "lpc17xx_clkpwr.h" /* If this source file built with example, the LPC17xx FW library configuration * file in each example directory ("lpc17xx_libcfg.h") must be included, * otherwise
in „LPC1768 Ethernet mit DP83848J“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
test_DMA2.c
(LED off) } void redLED(int on) { if (on) LPC_GPIO0->FIOCLR |= (1 << 22); else LPC_GPIO0->FIOSET |= (1 << 22); } void greenLED(int on) { if (on) LPC_GPIO3->FIOCLR |= (1 << 25); else LPC_GPIO3->FIOSET |= (1 << 25); } void blueLED(int on) { if (on
in „ARM LPC 1769 DMA Problem nach power-on“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
lpc3131_adc.c
"[lpc3131 adc] powersave_on, powersave_off\n"); printk(KERN_INFO "[lpc3131 adc] 0, 1, 3 - set channel 0/1/3\n"); printk(KERN_INFO "[lpc3131 adc] setres_8, setres_10 - set resolution\n"); printk(KERN_INFO "[lpc3131 adc] 101-200 - set averaging loops to (<value> - 100)\n"); printk(KERN_INFO "[lpc3131 adc] message format for ad-conversions: \"channel:resolution:value\"\n"); printk(KERN_INFO "[lpc3131 adc] BE
in „GNUBLIN www.gnublin.org“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
TODO: insert other definitions and declarations here int main(void) { uint32_t regVal; char portStat; LPC_SYSCON->SYSAHBCLKDIV = 1; //Keinen Prescaler für CORE LPC_SYSCON->SYSAHBCLKCTRL = 0x77FFF; //Alle Perepherie EIN LPC_SYSCON->SSP0CLKDIV = 1; LPC_SYSCON->UARTCLKDIV = 1; LPC_SYSCON->SSP1CLKDIV = 1; LPC_FLASHCTRL
in „LPC1113/302 debugging“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
emac.c
NULL; TX_DESC_CTRL( x ) = 0; TX_STAT_INFO( x ) = 0; } /* Set EMAC Transmit Descriptor Registers. */ LPC_EMAC->TxDescriptor = TX_DESC_BASE; LPC_EMAC->TxStatus = TX_STAT_BASE; LPC_EMAC->TxDescriptorNumber = NUM_TX_FRAG - 1; /* Tx Descriptors Point to 0 */ LPC_EMAC->TxProduceIndex = 0; } /*--------------
in „uIP doppelte Replys“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
zusammenfassung.txt
; /* CAN2 is p2.7 and p2.8 */ // LPC_PINCON->PINSEL4 |= 0x00014000; LPC_PINCON->PINSEL0 |= (1 << 9); /* Pin P0.4 used as RD2 (CAN2) */ LPC_PINCON->PINSEL0 |= (1 << 11); /* Pin P0.5 used as TD2 (CAN2) */ LPC_CAN1->MOD = LPC_CAN2->MOD = 1; /* Reset CAN */ LPC_CAN1->IER = LPC_CAN2->IER = 0; /* Disable Receive Interrupt */ LPC_CAN1->GSR = LPC_CAN2->GSR = 0; /* Reset error counter when CANxMOD is in reset */ LPC_CAN1->BTR = can_btr1; LPC_CAN2->BTR = can_btr2
in „LPC1768 Can und I2C funktionieren nicht zusammen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Errata_sheet_ES_LPC43X0_A.pdf
ES_LPC4350/30/20/10 Rev A Errata sheet LPC4350, LPC4330, LPC4320, LPC4310 Rev A Rev. 1.2 — 1 February 2012 Errata sheet Document information Info Content Keywords LPC4350FET256, LPC4350FET180, LPC4350FBD208, LPC4330FET256, LPC4330FET180, LPC4330FET100, LPC4330FBD144, LPC4320FET100, LPC4320FBD144, LPC4320FBD100, LPC4310FET100, LPC4310FBD144, Rev A errata Abstract This errata sheet describes both the known functional
in „Was sind das für MOSFET-Symbole?“ · Analoge Elektronik und Schaltungstechnik ·
-
Datei
s65main.c
) / 1000); LPC_TMR32B0->IR = 0xff; /* reset all interrrupts */ LPC_TMR32B0->MCR = 0x04; /* stop timer on match */ LPC_TMR32B0->TCR = 0x01; /* start timer */ /* wait until delay time has elapsed */ while (LPC_TMR32B0
in „S65 Display an LPC1114 (LPCXpresso Board)“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
/Warten bis PLL locked LPC_SYSCON->MAINCLKSEL = 3; //PLL als MAINCLK LPC_SYSCON->MAINCLKUEN = 0x01; //Update des MAINCLK LPC_SYSCON->MAINCLKUEN = 0x00; //Toggel des Updateregisters LPC_SYSCON->MAINCLKUEN = 0x01; while (!(LPC_SYSCON->MAINCLKUEN & 0x01)); //Warten bis upgedated LPC_SYSCON->SYSAHBCLKDIV = 1; //Keinen Prescaler für CORE LPC_SYSCON->SYSAHBCLKCTRL = 0x7FFFF; //Alle Perepherie EIN LPC_SYSCON->SSP0CLKDIV = 1; LPC_SYSCON->UARTCLKDIV = 1; LPC_SYSCON->SSP1CLKDIV = 1; LPC_IOCON
in „LPC1113/302 debugging“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
spi_test.c
per second */ uint32_t flag_timer = 0; void TIMER32_0_IRQHandler(void) { if (Chip_TIMER_MatchPending(LPC_TIMER32_0, 1)) { Chip_TIMER_ClearMatch(LPC_TIMER32_0, 1); if (Chip_GPIO_GetPinState(LPC_GPIO_PORT, 3, 1)) Chip_GPIO_WritePortBit(LPC_GPIO_PORT, 3, 1, false); else Chip_GPIO_WritePortBit(LPC_GPIO_PORT
in „LPC1343 IOCON_SCK0_LOC wirkungslos?“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
dma.c
********************************/ void DMA_Init( void ) { /* Enable CLOCK into GPDMA controller */ LPC_SC->PCONP |= (1 << 29); /* sync enabled */ LPC_GPDMA->DMACSync = 0xFFFF; LPC_SC->DMAREQSEL = 0x0000; /* Interrupt Flag im DMACIntTCStat für Channel 0 und 1 löschen*/ LPC_GPDMA->DMACIntTCClear = 0x03
in „DAC+DMA LPC1769“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
lpc11u3x.pdf
number Flash EEPROM SRAM USART I C-bus SSP USB ADC GPIO in kB in kB in kB FM+ device channels pins LPC11U34FHN33/311 40 4 8 1 1 2 1 8 26 LPC11U34FBD48/311 40 4 8 1 1 2 1 8 40 LPC11U34FHN33/421 48 4 10 1 1 2 1 8 26 LPC11U34FBD48/421 48 4 10 1 1 2 1 8 40 LPC11U35FHN33/401 64 4 10 1 1 2 1 8 26 LPC11U35FBD48/401 64 4 10 1 1 2 1 8 40 LPC11U35FBD64/401 64 4 10 1 1 2 1 8 54 LPC11U35FHI33/501 64 4 12 1 1 2 1 8 26 LPC11U35FET48/501 64 4 12 1 1 2 1 8 40 LPC11U36FBD48/401 96 4 10 1 1 2 1 8 40 LPC11U36FBD64/401 96 4 10 1 1 2 1 8 54 LPC11U37FBD48
in „LPC11U3 CRP zurücksetzen“ · Analoge Elektronik und Schaltungstechnik ·
-
Datei
i2c.c
*******************************************************/ uint32_t I2CInit( uint32_t I2cMode ) { // LPC_SC->PCONP |= (1 << 7); LPC_SC->PCONP |= (1 << 19); // power i2c1 // LPC_SC->PCONP |= (1 << 26); //LPC_SC->PCLKSEL1 |= (1<<6); ///////////// I2C1 P0.0=SDA1 P0.1=SCL1 //////////////////// //////////////////////// LPC_PINCON->PINSEL0 |= (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3); //0x0000000F; LPC_PINCON->PINMODE0 |=(1 << 1) | (1 << 3); // 0x0000000A; //0x0002900A; //pull up and down aus pin 0.0 0.1 LPC_PINCON->PINMODE_OD0
in „LPC1758 Problem mit I2C Bus“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
pwm.c
on PWMMR0, reset on PWMMR0, reset TC if PWM matches */ LPC_PWM1->MR0 = cycle; /* set PWM cycle */ LPC_PWM1->MR1 = cycle * 5/6; LPC_PWM1->MR2 = cycle * 2/3; LPC_PWM1->MR3 = cycle * 1/2; LPC_PWM1->MR4 = cycle * 1/3; LPC_PWM1->MR5 = cycle * 1/6; LPC_PWM1->MR6
in „LPC1769 PWM Probleme bei Dutycycle“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
lpc3131_adc.c
case ADC_POWERSAVE_OFF: printk(KERN_INFO "[lpc3131 adc] powersave off, adc always on\n"); break; case ADC_POWERSAVE_ON: printk(KERN_INFO "[lpc3131 adc] powersave on, adc always off\n"); break; case ADC_POWERSAVE_AUTO: printk(KERN_INFO "[lpc3131
in „GNUBLIN www.gnublin.org“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
lpc43xx_spi.c
/********************************************************************** * $Id$ lpc43xx_spi.c 2013-06-28 *//** * @file lpc43xx_spi.c * @brief Contains all functions support for SPI firmware library on lpc43xx * @version 1.0 * @date 28. June. 2013 * @author Rene Fritzsche * * Copyright
in „Cortex M0/M4 SPI nach CMSIS ?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
UM10398_-_LPC11xx_UserManual.pdf
UM10398 LPC111x/LPC11Cxx User manual Rev. 4 — 4 March 2011 User manual Document information Info Content Keywords ARM Cortex-M0, LPC1111, LPC1112, LPC1113, LPC1114, LPC11C12, LPC11C14, LPC1100, LPC1100L, LPC11C00, LPC11C22, LPC11C24 Abstract LPC111x/LPC11Cxx User manual NXP Semiconductors UM10398 LPC111x/LPC11Cxx User manual Revision history Rev Date Description 4 20110304 Modifications: • LPC111FHN33/102 and LPC11FHN33
in „Cortex-M UART im Polling-Betrieb“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
|= (1UL<<18); // output LPC_IOCON->P0_13 = 0; // %00000 LPC_GPIO0->DIR |= (1UL<<13); // output LPC_IOCON->P1_13 = 0; // %00000 LPC_GPIO1->DIR |= (1UL<<13); // output LPC_IOCON->P2_19 = 0; // %00000 LPC_GPIO2->DIR |= (1UL<<19); // output LPC_GPIO1->PIN |= (1UL<<18); // high LPC_GPIO0->PIN |= (1UL<<13); // high LPC_GPIO1->PIN &= ~(1UL<<13); // low LPC_GPIO2->PIN &= ~(1UL<<19); // low while (1) { // LED1 P1.18 LPC_GPIO1->PIN &= ~(1UL<<18)
in „Einstieg LPC4088 QuickStart Board“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
svpwm.c
#define GPIO_IN_PULLDOWN 0x03 #define GPIO_OUT_NORMAL 0x00 #define GPIO_OUT_OPENDRAIN 0x01 #define LPC_GPIO(a) (LPC_GPIO0 + a*(LPC_GPIO1-LPC_GPIO0)) #define GPIO_DIR_OUT(a,b) (LPC_GPIO(a)->FIODIR |= (1<<b)) #define GPIO_DIR_IN(a,b) (LPC_GPIO(a)->FIODIR &= ~(1<<b)) #define GPIO_SET(a,b) (LPC_GPIO(a)->
in „SVPWM mit LPC1769“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
/** * Includes * */ #include "lc798x.h" #include "lpc17xx.h" #include "lpc17xx_i2c.h" #include "lpc17xx_can.h" #include "lpc17xx_gpio.h" #include "lpc17xx_exti.h" #include "lpc17xx_timer.h" #include "lpc17xx_pinsel.h" #include "lpc17xx_libcfg_default.h
in „LPC1769 Kompass Sensor auslesen mit timer0 interrupt“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
ccan_rom.c
, }; SystemCoreClockUpdate(); Board_Init(); /*UART!! */ Init_UART_PinMux(); Chip_UART_Init(LPC_USART); Chip_UART_SetBaud(LPC_USART, 19200); Chip_UART_ConfigData(LPC_USART, (UART_LCR_WLEN8 | UART_LCR_SBS_1BIT)); Chip_UART_SetupFIFOS(LPC_USART, (UART_FCR_FIFO_EN | UART_FCR_TRG_LEV2)); Chip_UART_TXEnable(LPC_USART); /* Setup UART for 115.2K8N1 */ Chip_UART_Init(LPC_USART); Chip_UART_SetBaud(LPC_USART, 19200); Chip_UART_ConfigData(LPC_USART, (UART_LCR_WLEN8 | UART_LCR_SBS_1BIT)); Chip_UART_SetupFIFOS(LPC_USART
in „Weiterhin Probleme mit CAN auf LPC11C22“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
lpc43xx_cgu.c
/********************************************************************** * $Id$ lpc43xx_cgu.c 2013-06-30 *//** * @file lpc43xx_cgu.c * @brief Contains all functions support for Clock Generation and Control * firmware library on lpc43xx * @version 1.1 * @date 30. June. 2013 * @author
in „Cortex M0/M4 SPI nach CMSIS ?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
LPC3130_31.pdf
LPC3130/3131 Low-cost, low-power ARM926EJ-S MCUs with high-speed USB 2.0 OTG, SD/MMC, and NAND flash controller Rev. 2 — 29 May 2012 Product data sheet 1. General description The NXP LPC3130/3131 combine
in „LCD-Interface LPC3131“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
code.cpp
gesendet = 0, empfangen =0, arr[100], arrInd=0; for (int var = 0; var < 100; ++var) { arr[var]=0; } LPC_I2C0->I2CONSET = I2CONSET_STA; int var=0; while(!gesendet){ while(!((LPC_I2C0->I2CONSET & I2CONSET_SI) >> 3)); var =LPC_I2C0->I2STAT; switch (var) { case 0x8:{/* A Start condition is issued. */ LPC_I2C0
in „LPC176x & SC16IS752 I2C Register Lesen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
LPC_2119_2129_Datenblatt.pdf
LPC2119/LPC2129 Single-chip 16/32-bit microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC and CAN Rev. 02 Ñ 02 February 2004 Preliminary data 1. General description The LPC2119/LPC2129 are based
in „LPC 2129 Versorgungsspannung via PIN“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
LPC2129EB_REVB.pdf
LPC2129 Evaluation Board LPC2129 EB Features 1. General description ● Philips LPC2129 16/32-bit controller on a The LPC2129 Evaluation Board is a functionally handy DIP50 package complete and low cost controller
in „Einsteigerboard LPC2119(29/94)“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
**************************************************************/ void TIMER0_IRQHandler(void) { if((LPC_TIM0->IR & (1<<4)) == 0x01) // if MR0 interrupt { LPC_TIM0->IR |= 1 << 4; // Clear Capture interrupt flag UART0_Printf("Time capture:"); TimeOccupancy = LPC_TIM0->CR0; // Read Capture register 0 value
in „Count external pulses using LPC1768“ · µC & Digital Electronics ·
-
PDF
P89LPC933_934_935_936_6.pdf
P89LPC935FA PLCC28 plastic leaded chip carrier; 28 lSOT261-2 P89LPC933FDH TSSOP28 plastic thin shrink small outlineSOT361-1 P89LPC934FDH package; 28 leads; body width 4.4 mm P89LPC935FDH P89LPC936FDH P89LPC935FHN
in „AD-Wandlung p89lpc936“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
EU_Price_List_2011.pdf
NXP LPC1343 (Cortex-M3) 140.00 www.keil.com/mcb1000 MCB17xx Evaluation Board for NXP LPC175x and LPC 176x series (Cortex-M3) 250.00 MCB1800 Evaluation Board for NXP LPC1800 series (Cortex-M3) NEW! Available Q3,2011 260.00 MCB2140 Evaluation Board for NXP LPC214x series (ARM7TDMI) 170.00 MCB23xx Evaluation Board for NXP LPC2378 & LPC2388 (ARM7TDMI) 200.00 MCB24xx Evaluation Board for NXP LPC2460 & LPC2470 series (ARM7TDMI) 295.00 MCB2929 Evaluation Board
in „TFT240320TP an Savvy128v1.2“ · Mikrocontroller und Digitale Elektronik ·
