1 | mySmartUSB-commands (release 07/2010)
|
2 | =====================================
|
3 |
|
4 | content:
|
5 | 1. description
|
6 | 2. commands
|
7 | 3. batch-using and example
|
8 |
|
9 |
|
10 | 1. description
|
11 | ==============
|
12 |
|
13 | The firmware of the mySmartUSB programmer has
|
14 | beside the specific protocols (myMode, STK500, AVR9111/910/109)
|
15 | an own protocol available to address additional features
|
16 | of the mySmartUSB programmer.
|
17 |
|
18 | Use the baud rate according to the actual mode.
|
19 |
|
20 | protocol Light MK2 MK3
|
21 | ------------------------------------
|
22 |
|
23 | AVR911/910/109 X X X
|
24 | (baud 19200)
|
25 |
|
26 | STK500 X - X
|
27 | (baud 115200)
|
28 |
|
29 | myMode - - X
|
30 | (baud 500000)
|
31 |
|
32 |
|
33 | 2. commands
|
34 | ===========
|
35 |
|
36 | This additional protocol is activated by a identifier
|
37 | which had to be put in front of each command.
|
38 |
|
39 | myAVR-commands, starting with 0xE6='æ'=Alt+0230, 0xBA=0186
|
40 |
|
41 | "浺¹²³©" + command ( 0xE6 0xB5 0xBA 0xB9 0xB2 0xB3 0xA9 )
|
42 |
|
43 |
|
44 | command Light MK2 MK3 description
|
45 | ----------------------------------------------------------------
|
46 |
|
47 | + X X X turn on board power supply
|
48 |
|
49 | - X X X turn off board power supply
|
50 |
|
51 | r X X X release reset on the attached board
|
52 |
|
53 | i X X X return the Status of the programmer
|
54 |
|
55 | I - - x return ProgMode
|
56 |
|
57 | m - X X switch the programmer in myMode
|
58 |
|
59 | p - X (X) switch the programmer in programming mode
|
60 |
|
61 | d - X X switch the programmer in pass-through mode RS232
|
62 |
|
63 | s - - X switch the programmer in STK500 mode
|
64 |
|
65 | a - - X switch the programmer in AVR910 mode
|
66 |
|
67 | q - X X switch the programmer in quiet mode
|
68 |
|
69 | t X - - return emulationtype AVR911 ('a') or STK500 ('s')
|
70 |
|
71 | v X X X return version as string
|
72 | e.g. info ="2.03.1457"
|
73 |
|
74 | C - X X turn on RescueClock
|
75 |
|
76 | c - X X trun off RescueClock
|
77 |
|
78 | R X - - reset programmer
|
79 |
|
80 | B + xx - X - set baud rate; next Byte is UBRRL;
|
81 | 8MHz: 51=19200, 34=28800,25=38400, 16=57600, (12=76800), 8=115200
|
82 |
|
83 | W X - - powerOnBurn off
|
84 |
|
85 | w X - - powerOnBurn on
|
86 |
|
87 | % X - - return powerOnBurn on ('w') or off ('W')
|
88 |
|
89 | 3 X - - switch to 3V
|
90 |
|
91 | 5 X - - switch to 5V
|
92 |
|
93 | ^ X - - return board nominal voltage '3' or '5' Volt
|
94 |
|
95 | R - - x write current mode and ProgMode to EEPROM
|
96 |
|
97 |
|
98 | confirmation from the programmer: ["÷"+infos]+"÷±"+code+"\r\n"
|
99 |
|
100 |
|
101 | 3. batch-using and example
|
102 | ==========================
|
103 |
|
104 | To perform a special command, you can call _mySmart.cmd.
|
105 |
|
106 | This file has to be called with 2 parameters:
|
107 | 1.para=COM-port
|
108 | 2.para=CmdTxt-file
|
109 |
|
110 | samlpe: _mySmart.cmd COM3 BoardPowerOn.txt
|
Schaltplan.png
(4,3 KB)
Board.png
(2,5 KB)
Schaltung0.png
(780 KB)
Schaltung1.png
(800 KB)
Schaltung2.png
(780 KB)
