-
Artikel
AVR Bootloader optiboot Assemblerversion
hier die Pinne A3 und A4 von der Software benutzt. Ein UART ist ja auch nicht vorhanden beim ATtiny84. Wir wollten ja aber nur einen Pin für die serielle Kommunikation benutzen. Das ist einfach möglich durch die Benennung des gleichen Wunschpins für TX und RX. Also muß der Aufruf make attiny84 LFUSE=
für eine ATtiny84. make attiny84 Optiboot für 8000000 Hz (8.00 Mhz) Betrieb mit Baudrate 57600 und EEprom Unterstützung konfiguriert. >>> Starte optiboot für AVR attiny84 erstellen: LED-Pin PA4 benutzt Pin 9-PDIP14 1-
-
Artikel
MOSFET-Übersicht
20 3,7 1,3 65 2,5V LL Rei,csd,Bü 0,15 IRLML6302PBF SOT-23 IRF 1,5 20 0,75 0,54 600 Rei,csd,Bü 0,18 BSS83P SOT-23 Inf 2,0 60 0,33 0,36 2000 nicht mit BSS83 (ohne P) verwechseln Rei 0,11 BSS84 SOT-23 Fairchild,NXP 2,0 50 0,13 0,35 10000 - Fa 0,28 BSS110 TO-97, SOT-23 Phi 3,0 50 0,17 0,35 10000 - - - PMV65XP
LL, LIN Rei 0,092 BSS138 SOT-23 div 0,8-1,6 50 0,22 0,36 2000 5V LL, LIN Rei 0,06 BSS123 SOT-23 div 0,8-1,6 100 0,17 0,36 10000 @ 4,5V, 4,5V LL, LIN Rei 0,06 IRFP2907 TO-247AC irf 4,0 75 209 470 4,5 Rei 2,70 2N7000 TO-92
-
Artikel
Batteriewächter
für den Taster. Über T2 wird der Spannungsteiler für die Batteriespannung stromlos geschaltet. Der BSS138 ist ein FET mit geringer UGS threshold voltage von max. 1.5V. Er begrenzt also am Source die Drain-Spannung auf VCC-1.5V. Da die Referenzspannung 1.2V beträgt, ergibt sich durch den FET bei einer
Layout (PDF) Batteriewächter BMON1048 Stückliste Batteriewächter BMON1048 Weblinks. L200_Datasheet BSS84P_Datasheet BF245C_Datasheet BF545C_Datasheet XC6216_Datasheet PIC18F2520_Datasheet LM385Z-1.2_Datasheet BSS138_Datasheet LCD-2-13 LT1763_Datasheet Gehäuse_EG2 GC-Prevue Gerber viewer Siehe auch. Forum
-
Artikel
ARM-ASM-Tutorial
used to get the beginning of the initialization data in flash, and assign it to “_DataLoad”. The “.bss” section contains all the variables that should be zero-initialized, and the symbols “_BssStart” and “_BssEnd” are set to its beginning and end address, respectively. It is marked with “NOLOAD” as well
location counter to make sure the address is a multiple of 4. The same thing is done right before “_BssEnd” and also at the end of the “.text” section, to make sure that “_BssEnd” and “_DataLoad” are multiples of 4 as well. The only thing left is the actual initialization of the RAM. To do that, change
-
Artikel
Reichelt-Wishlist
für Endstufen * BF556 (SMD-Version vom BF256) | BFG35 | BSH205 P-Channel 1.5V(GS), 0.75A, 12V D-S | BSS606N Logic Level N-MOSFET 60V/3,2A SOT-89 | BUF420AW Schaltnetzteil Transistor von STM | IPW60R045CS Infineon MOSFET 600V 45mOhm Rdson 30ns tr+tf (niedrigster Rdson in der Klasse) | Si4562DY N- and P-Channel
* Dual N-Kanal-MOSFETs z. B. Diodes DMN63D8LDW-7 (260 mA/30 V/2,8 Ohm, 1,5V U_GSth) oder Nexperia BSS138BKS,115 (320 mA/60V 1 Ohm, 1,1 V U_GSth); ideal für I2C-Levelshifter | TVS-Diode für RS-485: Bourns CDSOT23-SM712 | Ideale Diode TI LM66100 | Op-Amps, MOSFET-Treiber. LME49710/20/40 Audio-Opamps von
-
Artikel
Standardbauelemente
, 5Ω On-Widerstand veraltete Technik, aber in bastelfreundlichem TO-92 Gehäuse R,D PDF (Fairchild) BSS123 0,05 max 100V, max 170mA (cont.), Thresholdspannung 1,7V, On-Widerstand 1,3Ω SOT23 SMD-FET, auch für 3V3-versorgte Schaltungen bestens geeignet R,D PDF (Fairchild) BUK100-50GL 1,15 Logic-Level Power
Anwendungen Lieferant Daten- blatt KTY81 0,50 nichtlinear(*), bis 150°C in C Schaltungen R, D PDF KTY84 0,72 nichtlinear(*), bis 300°C in C Schaltungen R PDF Pt100 / Pt1000 ab 3,00 lineare Kennlinie analoge Messschaltungen F C R (*) Verschaltet man den Sensor als Spannungsteiler (Abgriff an den ADC), so