) DD BAT o V BAT= 3.0V – 4.5V (for charge bump regulator circuit) o V CC = 7.5V – 16.5V (for Panel driving) Segment maximum source current: 240uA Common maximum sink current: 30mA Embedded 128 x 64 bit
) DD BAT o V BAT= 3.0V – 4.5V (for charge bump regulator circuit) o V CC = 7.5V – 16.5V (for Panel driving) Segment maximum source current: 240uA Common maximum sink current: 30mA Embedded 128 x 64 bit
PHY_INT_N 55 PHY_CLK125 R57 CLK125_NDO/LED_MODE 4K99 56 RESET_N R40 DVDDH D D D D D D D D D D D D8 N N N A N N N N N N N 10K A A A E D D D D D D D 3 9 3 5 7 8 3 8 4 9 3 U8 6 6 1 1 2 2 3 3 5 1 4 3 + C58 PHY_RESET_N 2 VDD OUT 1 CLK_25MHZ 10UF GND CONT 16v BAT54A/SOT 2 25MHZ A A HPSDR Copyright 2012 - Kevin
1 2 3 4 5 6 USB & MCU Spannungsversorgung Senosren A A File: USB & MCU.kicad_sch File: Spannungsversorgung.kicad_sch File:Sensoren.kicad_sch B B C C Sheet: / D D File: ESP32_PCB_D3.kicad_sch Title: Size: A4 Date: Rev: KiCad E.D.A. 9.0.6 Id: 1/4 1 2 3 4
1 2 3 4 5 6 USB & MCU Spannungsversorgung Senosren A A File: USB & MCU.kicad_sch File: Spannungsversorgung.kicad_sch File:Sensoren.kicad_sch B B C C Sheet: / D D File: ESP32_PCB_D3.kicad_sch Title: Size: A4 Date: Rev: KiCad E.D.A. 9.0.6 Id: 1/4 1 2 3 4
BAT position, a 20 mm coin cell battery in the CR2032 socket can be used to power the device. With the switch in this position, no current measurements are active. This is the recommended switch position
, Seite A I_exc 1,00 mA 0,1 mW am Pt100, wenig Eigenerwärmung T2 S+ Sense hochohmig, Seite A R_ref 100 Ω 0,1 R_pt = R_ref · V_sense / V_ref T3 S− Sense hochohmig, Seite B % T4 F− Stromrückführung über R_ref R_prot
TP214 1 1 1 1 2 PB0 PB3 5 3 VCC3V3 C C C TP151 3 GND VCC 4 2 TP152 PB1 PB2 VCC5V_PROG TP153 C1203 BAT54CW R1212 100nF 10K 8 7 6 5 R1214 100R D1203 1 2 1 2 3 4 T K D1204 1 2 A L I I T D1205 1 2 T T R 5 D1206 1 2 5 5 5 5 P P P P T T T T 2 - 8 GRUNDIG Service Chassis G5 Chassisplatte / Chassis Board –
1 2 . D 1 9 2 0 2 7 1 6 5 3 2 2 2 0 9 5 4 6 9 7 D 1921 N74LSO00N 5322 209 84823 9 9 6. CIRCUIT D I A G R A M S A N D P.C.B. L A Y - O U T S : , e SLIDER D R A W N IN FUNCTION V z ; . V-Urms V = A = a 35 30 25 19 15 10 5) 1 TRIGGER Ss °C L E V E L . ok ots $73229 — — | ) 3102 S L I D E R Fig.54.Switchp.c.b.lay-out
their central locking system, which opens the doors, is bat- vehicles. From 1995 it is mandatory that all cars sold in tery powered, operates at a ultra-high frequency (UHF) the EU are fitted with such an immobilizer device, ac- of 433 MHz, and only activates
capacity of the scale The weight display – The load plate (3) – Position the platform shows “L” or “Err 54” is not in place The weight display – The display did not show – Press the =/z briefly shows “Err 02” a zero readout when the key (14); then press the =/z key (14) =/z key again was pressed to calibrate
H 5P 3131A/1/132A2 25 M Hz reältltlichen O ptionen erdenn im A nschlußß a diesenen A bsatz aufgelistet. Die en tsprecheuden echnischenn Duten fü dr ie O ionen b inden sen ich in K apitell , "e chnischee D ten .
Bild
Bild
Bild
Bild
Bild
