Datasheet 3.5V to 60V Input 1ch Boost DC/DC Controller BD9615MUV-LB General Description Key Specifications This is the product guarantees long time support in Input Voltage Range: 3.5V to 60V Industrial market. Reference Voltage Precision: (Ta=25°C) 0.8V±1.5% (Ta=-40°C to +105°C) ±2.0% BD9615MUV-LB is a low side MOSFET controller with Frequency Range: 100kHz to 2500kHz high withstand voltage (60V). It is suitable for circuits Operating Temperature Range: -40°C to +105°C requiring
reserved, test signal for production test 1001 reserved 1010 HIGH 1011 LOW 1100 TxActive: at 106 kBd: HIGH during Start bit, Data bit, Parity and CRC at 212 kBd: 424 kBd and 848 kBd: HIGH during data and CRC 1101 RxActive: at 106 kBd: HIGH during Data bit, Parity and CRC at 212 kBd: 424 kBd and 848 kBd: HIGH during data and CRC 1110 subcarrier detected: 106 kBd: not applicable 212 kBd: 424 kBd and 848 kBd: HIGH during last part of data and CRC 1111 test bus bit as defined by the TestSel1Reg register
2. C in + CO** 0.1 F 1.0 F R2 ORDERING INFORMATION Operating Device Temperature Range Package LM317BD2T Surface Mount **▯inis required if regulator is located an appreciable distance from power sLM317BTilter. TJ= –40⋅ to +125⋅C Insertion Mount **▯O is not needed for stability, however, it does improve
Low Noise Negative LDO Post Regulator Up to 50mA ersthe negativeLDOregulator.EachLDOcanprovideup nn 135µA Quiescent Current in Burst Mode Operation ® to 50mA of output current. The LDO output voltages can be adjusted using external resistor dividers. with Both LDO Regulators On nn 50kHzto500kHzProgrammableOscillatorFrequency
) eff The bias-dependent threshold voltage depends on the bulk-source BSlor the bulk-drain voltage BD depending on the mode of operation. √ √ γ · Φ − VBS − Φ for DS ≥ 0, i.eBSV≥ V BD VTh= V T0+ γ ·√ Φ − V − √Φ for V < 0, i.e. V > V (11.160) BD DS BD BS The following equations describe the DC current
・ または全てが異常 V1-4 INVALID ITEM HDMI output TV C3-2. MUTE H HDMI HDMI NET CPU への MUTE Hi 接続をチェックします。 BD/DVD player HDMI OUT C3-2 MUTE H: OK CB1 CB2 CB3 CB4 IC1 HDMI HDMI HDMI HDMI HDMI HDMI IN4 IN3 IN2 IN1 OUT RECEIVER/TRANSMITTER C3-3. MUTE L MN864798 NET CPU への MUTE Lo 接続をチェックします。 IC1 C3-3 HDMI MUTE
300, 500, 600, 800, 900, 1000, 1200, 8000 ohms can be selected with preset k n o b Resolution 01.dBdB for signals < 10mVv Number of representation units £999 for signals < 10 m V Acuracy +Signals >10mV:0.2dB Signals < 1 0 m V : 1dB Temperature coefficient £0,013 dB/°C. Input impedance 110 M Q + 1 %
n l s l s c n n s t d l t v s v s i W o e t e m o l e e e e h I t m V t y e - s n s n H s u l e w bd t r . u h u h I i V l l t S a g « i d t d t L c R o o g / s i / c A e A e G t E t t i 8 n s i V e – e + e E i V n n + P/ V - r » i j a » s » S » S e O C C T 1 A s 1 2 3 4 u 1 t r r p a t t e r s e p
Coupling:: AC VSWR:R: <2. :1 P owerr Range and Sensit vityy (Sinusoid) WOMH z to 2.7GHz:: -27dBm to+19 Bd 2.77GHzzto 3GHz:z: -21dBm to+13 Bd Da magee Lvel: ; 5 Vr s Exte rnal Arm Inpu S t pecif ica tons Exte rnal lrm Inp t Cha a r cteri s cs Signall Iput R nge: Impedance:: 1KQΩ High-Level Input: >3.0VV Input
of the A6 CPU board for the following discussion. System Clock Three clock drivers, U47, U49, and U135, generate the various 25 MHz clocks used throughout the CPU. These clock drivers are synchronized by the output of Y2, a 12 MHz oscillator. Reset The power supply reset signal (PWRDY) is ANDed with
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
Bild
