Schalter Ein/Aus LED rot 2 mA 3,3k LM358 Buchsen A K D BS170 A S 20 8 61,9 10 5 12,4 2,49 5 2 619 1 1 124k 0,3 2,49k 0,2 6,19k 0,1 12,4k LED-Tester Nils Hintz 2003, 2015 LM358 K A D G S
Schalter Ein/Aus LED Buchsen Durchschalter Prüfstrom
rot 2 mA
3,3k LM358
100n
K BS170
A
20 8 61,9
124
10 6 249
5 6 619
2 2 1,24k
1 1 2,49k
0,5 2 6,19k
0,1 2 12,4k
0,2 mA
LM358-1.2
LED-Tester
Nils Hintze 2008, 2015
LM358
K A D G S
Dieser Plan ist geistiges Eigentum von Nils Hintze und
GPIO2 C4 3 A9 GPIO13 GPIO15 GPIO15 WS2812 4 GDN VCC GND R10 100nF LM358N VCC B0 Q1 4 6 +3V3 2 k 82 BS170 R8 7 DCF77 1 0 0 a R 1 R 1 4 n LED1 680 5 4 12 T t DCF IC2B T DD B O R8, LED1 und IC2 nur erforderlich, GND B 2 wenn DCF verwendet wird D GND GND GND GND AMS1117 3 1-2 > RUN 3 V A A V 3 2-3 > PROG
für Thermo- und Ausgleichsleitungen Thermopaar IEC 60584-3: 2007 nach Stromkreise DIN 43713: 1991 BS 1843 NFC 42324 ANSI MC96.1 JIS C 1610-1981 DIN EN 60584-3:2008 bzw. DIN EN 60584-3:2008 bzw. Klassen der Einsatz- Thermo- Ausgleichs- IEC 60584-3: 2007 IEC60584-3: 2007 Grenzabweichungen temperatur Temperatur
O-—o™B VOLTAGE INPOT ATTENUATOR CONVERTOR ; 811127 is S365 Fg.9.Blockdiagram-frequencymeasurements bs 13 1.3.3.2. Time measurements Time measurements of signals are determined in conjunction with the trigger level function in a similar way to frequency measurements. . ; The input signal isapplied via
Pin Discriptions Pin FPinNo.ns Symbol Description PinNo. Symbol Description High-side Boost input. 1 BS HiBS supplies the drive for High-side Nch-MOSFET switch. 1 BS BSConnect a capacitor and a resistor between SW to BS. CoPower input. IN supplies the p wer to the IC as well as the regulator switches 2
ee eeeeeee sees Bl 52, Dismantling the battery power supply (PM2519/21} 0 . 0. s.eece.ee veces ees BS 53. Dismantlitnhge 1EC-bus and the galvanic separation .. 0... 0 . 2 .ee.s e.ee ee ees 5 6 6. PARTS LIST 61 61. Main pob... 202. e eee eee e eee eeee eeect eee eee eence te cence nes Gel 61.4. Resistors
LED Board and Lens. – Fig. 1: HaltBr in Pfeilrichtung schieben und abnehmen. – Fig. 1: Push the holdeBs in arrow direction and remove it. – Fig. 2/4: Gerät wie abgebildet auf eine weiche Unterlage legen. – Fig. 2/4: Lay device as shown on a soft pad. – Fig. 2: Alle seitlichen SchraubCn herausdrehen. –
appropriate menu code. The “control range” lies between approx.30% of the lower tolerance limit and170% of the upper tolerance limit. Control lines are activated: Code Changes Only within the control range 4 3 1 Always 4 3 2 * Only at stability within the control range 4 3 3 Only at stability 4 3 4 *
]COMP ‘oor[2] M5] vREF- v- [ 3| fi4| VREF+ wseBi [5 | /13BB LSB e? Ls | [ 187 B3 110} a6 e [a | 9] Bs ST4gé5 8 6 0 2 2 8 Figure 3.16 Pin connect ions 3 - 2 5 3.7.4 -LP o w e R e s G e n e r a t o rr (watchdog) - Automatic Reset Generation After Voltage Drop - Wide Supply Voltage Range ... 3 V to 18 V
to 10 % 35 % to 50 % 22Na 511 7.5 % to 9.0 % 13 % to 25 % 13Cs 662 6.5 % to 8.5 % 11 % to 20 % 60 1,170 5 % to 6.5% 8.5 % to 11 % Co 1,330 4.5 % to 5.5 % 8.0 % to 9.5 % Table 7-2: Energy resolution for typical gamma-rays, obtained with NaI(Tl) or BGO scintillator 162 CHAPTER 7 SCINTILLATION COUNTING Energy
Bild
Bild
Bild
Bild
Bild
Bild
Bild
