-
PDF
datasheet.pdf
TA= 25°C, CIN C OUT= 0.1 μF, unless otherwise noted. Table 2. Parameter Symbol Conditions Min Typ Max Unit OUTPUTVOLTAGE VO A Grade 2.045 2.048 2.051 V B Grade 2.047 2.048 2.049 V INITIAL ACCURACY VOERR A Grade 3 mV 0.15 % B Grade 1 mV 0.05 % TEMPERATURE DRIFT TCVO A Grade −40°C <TA< +125°C 2 10 ppm
in „Datenblatt richtig lesen“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
JBT6K71-AS_A__v1.42_2006-02-07_E.PDF
correction) with software-programmable display color modes • High-speed interface operation: 20 MHz max. (when high-speed write function is used) • A broad range of display color control (batch display switching by software) • 262,144-color mode • 65,536-color mode • 8-color mode • Supply voltage: Digital
in „LCD aus Benq EL71 Handy“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Vishay-293D.pdf
(+) code B, C, D, E Cases A Case Note (1)Capital letter indicates lead (Pb)-free STANDARD RATINGS MAX. DCL MAX. DF MAX. ESR MAX. RIPPLE CAPACITANCE CASE CODE PART NUMBER AT +25 °C AT +25 °C AT +25 °C 100 kHz (μF) (μA) 120 Hz 100 kHz IRMS (%) () (A) 4 VDC AT +85 °C; 2.7 V DC AT +125 °C 2.2 A 293D225
in „Was ist das für ein Bauteil? (Aus einem Autoschlüssel)“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Ferroxcube_Data_Handbook.pdf
, Test Tb, method 1B: 350 °C, 3.5 s Solderability “IEC 60068-2-20”, Part 2, Test Ta, method 1 16.6 max. 19.1 max. handbook, full pagewidth 3.81 22.7 10 11 7.4 6.1 22.7 max. 15.24 ±0.1 ±0.1 ±0.1 ±0.1 15.24 max. 3.81 CBW264 9.25 9.2 min. min. 10 11 7.4 6.1 15.3 17.5 ±0.1 ±0.1 ±0.1 ±0.1 max. max. 3.8 5.95
in „Maximale Magnetflussdichte im Ferritkern Temperaturangabe“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
S29GL512N.pdf
Max 25 25 35 35 ns C t t Output Enable to Output Delay Max 25 25 35 35 ns GLQV OE EHQZ DF Chip Enable to Output High Z (Note 1) Max 20 ns tGHQZ DF OutputEnabletoOutput HighZ(Note1) Max 20 ns t t Output
in „PHILIPS VP5500 VoIP Telefon bei Pollin“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
293d.pdf
Vishay marking A Case B, C, D, E Cases Note (1)Capital letter indicates lead (Pb)-free STANDARD RATINGS MAX. DF MAX. ESR MAX. RIPPLE CAPACITANCE MAX. DCL AT +25 °C AT +25 °C 100 kHz (μF) CASE CODE PART NUMBER AT +25 °C 120 Hz 100 kHz I (μA) (%) (Ω) (A) 4 VDC AT +85 °C; 2.7 VDC AT +125 °C 2.2 A 293D225(1)004A
in „Suche dringend passenden SMD Kondensator“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
APT_Communications_Protocol.pdf
35 Data Part No/Axis Serial Number Counts per Unit 36 37 38 39 40 41 42 43 44 45 46 47 Data MinPos Max Pos Max Accn 48 49 50 51 52 53 54 55 56 57 58 59 Data Max Dec Max Vel Reserved Reserved 60 61 62 63 64 65 66 67 68 69 70 71 Data Reserved Reserved Reserved Reserved 72 73 74 75 76 77 78 79 Data Reserved
in „Thorlabs Laser-Source mit über FTDI232BM ansteuern“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
opa354.pdf
Plane 1 4 0.010 (0,25) A 0°– 8° 0.044 (1,12) 0.016 (0,40) Seating Plane 0.010 (0,25) 0.069 (1,75) MAX 0.004 (0,10) 0.004 (0,10) PINS ** 8 14 16 DIM A MAX 0.197 0.344 0.394 (5,00) (8,75) (10,00) A MIN 0.189 0.337 0.386 (4,80) (8,55) (9,80) 4040047/E 09/01 NOTES: A. All linear dimensions are in inches
in „OP Verstärker scheint zu schwingen“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
ST7036-V1.4.pdf
after power on and external MPU interface enabled reset pin " 80 x 8-bit display RAM (80 characters max.) " Internal oscillator(Frequency=540kHz) and " 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) " Built-in voltage booster and follower circuit " 64 x 8-bit
in „EA DOG-M Display (ST7046) und customchars. ARGH!“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „DOG-M-Display/ST7036 Initialisierung“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ST7036-V1.7.pdf
controller/driver after power on and external enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „DOG-M-Display/ST7036 Initialisierung“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
LCD-Controller_ST7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „DOG-M mit ATmega8 in Assembler ansteuern“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „Initialisierungsfolge fuer EA DOGM 163 SPI 3.3V“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „DOG-M Display über SPI“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „LCD " ° " Zeichen aus Zeichensatz anzeigen?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „Controller ST7036“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ST7036-V1.7.pdf
controller/driver after power on and external enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „Newbie Probleme bei LCD DOGM Initialisierung in Assembler“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
-
PDF
st7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „STK500 und LCD (ST7036) Problem“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ST7036.pdf
after power on and external MPU interface enabled reset pin z 80 x 8-bit display RAM (80 characters max.) z Internal oscillator(Frequency=540kHz) and z 10,240-bit character generator ROM for a external clock total of 256 character fonts(max) z Built-in voltage booster and follower circuit z 64 x 8-bit
in „i2C TWI Modus - ST7036 - DOGM DOGM162 DOGM081 EA DOGM163, ist das Möglich ?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
150418-da-01-en-ADJ_LOW_DROPOUT_POS_VR_5A.pdf
operating temperature range, otherwise specifications are at T = 25°C. A PARAMETER CONDITIONS MIN TYP MAX UNITS Output Voltage LT1084-3.3 IOUT = 0mA, TJ= 25°C, VIN 8V (K Package Only) 3.270 3.300 3.330 V 4.8V V IN 15V, 0 I OUT FULLOAD (Notes 3, 4, 9) 3.235 3.300 3.365 V LT1085-3.3 V IN5V, I OUT = 0mA, TJ
in „spannungsstabilisierung in blitz“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
1083ffd.pdf
operating temperature range, otherwise specifications are at T = 25°C. A PARAMETER CONDITIONS MIN TYP MAX UNITS Output Voltage LT1084-3.3 IOUT = 0mA, TJ= 25°C, VIN 8V (K Package Only) 3.270 3.300 3.330 V 4.8V ≤V IN5V, 0 ≤ I OUT ≤ FULLOAD (Notes 3, 4, 9) ● 3.235 3.300 3.365 V LT1085-3.3 V IN5V, I OUT = 0mA
in „Frage zum Datenblatt LT1084CT-5“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
AD7416_7_8_f.pdf
LSB max Internal Reference. Gain Error Match ±0.6 ±0.6 LSB max AD7417 Only. 2 Offset Error ±4 ±4 LSB max Offset Error Match ±0.7 ±0.7 LSB max AD7417 Only. ANALOG INPUTS Input Voltage Range VREF V REF V max
in „I²C-Code - fehlt noch was?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
NT7538-LCD-Controller-Datasheet.pdf
Control Timing CL (Output) tDFR FR (VDD = 2.7 ~ 3.6V, Ta= -40 ~ +85C) Symbol Parameter Min. Typ. Max. Unit Condition tDFR FR delay time - 20 80 ns CL = 50 pF (VDD= 1.8 ~ 2.7V, Ta= -40 ~ +85C) Symbol Parameter Min. Typ. Max. Unit Condition tDFR FR delay time - 40 160 ns CL = 50 pF 5. Reset Timing RW
in „[Pollin] Grafik Display Anschluss Verständnisfragen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
datasheet-23.pdf
= 1, RL= 2 kΩ, unless otherwise noted. Table 1. A Grade B Grade Parameter Test Conditions Min Typ Max Min Typ Max Unit COMMON-MODE REJECTION RATIO (CMRR) CMRR DC to 60 Hz with 1 kΩ VCM= ±10 V Source Imbalance G = 1 78 86 dB G = 10 94 100 dB G = 100 94 100 dB G = 1000 94 100 dB CMRR at 5 kHz VCM= ±10
in „Puls von EKG ableiten und weiterverarbeiten“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
MLX90640-Datasheet-Melexis.pdf
Figure 2 MLX90640 Overview and pin description 7. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max. Unit Remark Supply Voltage (over voltage) V 5 V DD Supply Voltage (operating max voltage) V 3.6 DD Reverse Voltage (each pin) -0.3 V Operating Temperature TAMB -40 +85 °C Storage Temperature TST -40
in „MLX90640 IR-Array 32x24 pixel“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
MLX90640-Datasheet-Melexis.pdf
Figure 2 MLX90640 Overview and pin description 7. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max. Unit Remark Supply Voltage (over voltage) V 5 V DD Supply Voltage (operating max voltage) V 3.6 DD Reverse Voltage (each pin) -0.3 V Operating Temperature TAMB -40 +85 °C Storage Temperature TST -40
in „Wärmebildkamera mit dem MLX90640 und Arduino Due“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
EMMC-32GB-2.pdf
Maximum read current at VDD_R_CURR_MIN 3 R [61:59] 7h V DD,min Maximum read current at VDD_R_CURR_MAX 3 R [58:56] 7h V DD,max Maximum write current at VDD_W_CURR_MIN 3 R [55:53] 7h V DD,min PDF: 09005aef84d69f8a Micron Technology, Inc. reserves the right to change products or specifications without
in „Pinout Flexansvhlusskabel 8-Pin an eMMC Flash-Card 32GB gesucht“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
SSD1332_R1.61.pdf
Peripheral Interface. It has a 256 steps contrast control and 65K color control. 2 FEATURES Support max. 96RGB x 64 matrix panel Power supply: V DD= 2.4V - 3.5V VCC= 7.0V - 18.0V OLED driving output voltage, 16V maximum DC-DC voltage converter Segment maximum source current: 200uA Common maximum sink
in „OLED und 8051“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
AD8606.pdf
Dimensionsshowninmillimeters 2.90 BSC 5 4 1.60 BSC 2.80 BSC 1 2 3 PIN 1 0.95 BSC 1.30 1.90 1.15 BSC 0.90 1.45 MAX 0.22 0.08 10° 0.15 MAX 0.50 SEATING 5° 0.60 0.30 PLANE 0° 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178-AA Figure58.5-LeadSmallOutlineTransistorPackage[SOT-23] (RJ-5) Dimensionsshowninmillimeters 3.20 3.00 2.80 8 5 5.15 3.20 4.90 3.00 1 4.65 2.80 4 PIN 1 0.65 BSC 0.95 0.85 1.10 MAX 0.75 0.80 0.15 0.38 0.23 8° 0.60 0.00 0.22 0.08 0° 0.40 COPLANARITY SEATING 0.10 PLANE COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure59.8-LeadMiniSmallOutlinePackage[MSOP] (RM-8) Dimensionsshowninmillimeters
in „Aktives Filter (Differential), Uref“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
XC6216.pdf
SETTING VOLTAGE 2% ACCURACY 1% ACCURACY OUT=20mA OUT=100mA V OUT(T) VOUT VOUT Vdif1 Vdif2 (V) MIN. MAX. MIN. MAX. TYP. MAX. TYP. MAX. 2.0 1.960 2.040 1.980 2.020 450 600 1900 2600 2.1 2.058 2.142 2.079 2.121 450 600 1900 2600 2.2 2.156 2.244 2.178 2.222 390 520 1700 2200 2.3 2.254 2.346 2.277 2.323 390
in „Suche Spannungsregler mit kleinem Ruhestrom <<2mA“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
XC6216.pdf
SETTING VOLTAGE 2% ACCURACY 1% ACCURACY OUT=20mA OUT=100mA V OUT(T) VOUT VOUT Vdif1 Vdif2 (V) MIN. MAX. MIN. MAX. TYP. MAX. TYP. MAX. 2.0 1.960 2.040 1.980 2.020 450 600 1900 2600 2.1 2.058 2.142 2.079 2.121 450 600 1900 2600 2.2 2.156 2.244 2.178 2.222 390 520 1700 2200 2.3 2.254 2.346 2.277 2.323 390
in „Suche Linearregler 5V für ca. 100uA minimal / 100mA max.“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
Google_Uebersetzer-Prescaler_12_Ghz.html
8px;margin-left:12px}@media screen and (min-width:361px){.gb_l.gb_9a{width:354px}}@media screen and (max-width:361px){.gb_l.gb_9a{width:calc(100vw - 12px *2)}}.gb_l.gb_9a.gb_ab{max-height:-webkit-calc(100vh - 44px - 100px);max-height:calc(100vh - 44px - 100px)}.gb_l.gb_9a.gb_bb{max-height:-webkit-calc(
in „Vorverstärker und Vorteiler für Frequenzzähler“ · HF, Funk und Felder ·
-
PDF
edison-module_HG_331189.pdf
specification for standard/fast mode I C bus devices Symbol Parameter Standard Fast Unit Notes Min Max Min Max fSCL SCL clock frequency 0 100 0 400 KHz tHD: STA Hold time (repeated) START condition. After this period, 4.0 – 0.6 – µs the first clock pulse is generated tLOW LOW period of the SCL clock
in „Intel Edison Breakout Board“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
s35i_c35i_m35i_atc_commandset_v01.pdf
supported <index>s), <nlength>, <tlength> OK/ERROR/+CME ERROR Parameter <index> Location number <nlength> Max. length of telephone number <tlength> Max. length of text corresponding to the number Write command Response AT+CPBR= +CPBR: <index1>, <nummer>, <typ>, <text>[<CR><LF> +CPBR: ..... <index1> +CPBR: <
in „Problem: Siemens C35 per Mikrocontroller steuern funktioniert nicht?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
s35i_c35i_m35i_atc_commandset_v01.pdf
supported <index>s), <nlength>, <tlength> OK/ERROR/+CME ERROR Parameter <index> Location number <nlength> Max. length of telephone number <tlength> Max. length of text corresponding to the number Write command Response AT+CPBR= +CPBR: <index1>, <nummer>, <typ>, <text>[<CR><LF> +CPBR: ..... <index1> +CPBR: <
in „AVR an Handy C35“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
AT_commandset.pdf
supported <index>s), <nlength>, <tlength> OK/ERROR/+CME ERROR Parameter <index> Location number <nlength> Max. length of telephone number <tlength> Max. length of text corresponding to the number Write command Response AT+CPBR= +CPBR: <index1>, <nummer>, <typ>, <text>[<CR><LF> +CPBR: ..... <index1> +CPBR: <
in „Simens S 35; AT-Befehle“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
semtech-sc4503.pdf
www.semtech.com SC4503 POWER MANAGEMENT Outline Drawing - TSOT-23 DIMENSIONS A DIM INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX e1 A - - .039 - - 1.00 D A1 .000 - .004 0.00 - 0.10 A2 .028 - .035 0.70 - 0.90 N b .012 - .020 0.30 - 0.50 2X E/2 c .003 - .008 0.08 - 0.20 E1 E D .110 .114 .118 2.80 2.90 3.00 E1 .060 .063
in „Welcher Schaltregler ist das?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ATtiny261A_Complete.pdf
Mode of Operation TOP Update of OCRx at TOV Flag Set on 0 0 0 0 Normal, 8-bit Mode 0xFF Immediate MAX (0xFF) 1 0 0 1 CTC Mode, 8-bit OCR0A Immediate MAX (0xFF) 2 0 1 X Normal, 16-bit Mode 0xFFFF Immediate MAX (0xFFFF) 3 1 0 X Input Capture Mode, 8-bit 0xFF Immediate MAX (0xFF) 4 1 1 X Input Capture
in „USI Interface als SPI Schnittstelle beim ATtiny261A“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
stepping_motor_Mdrive__OM-MD_V06.28.2002__e.pdf
Specifications ! Electrical Specifications Mechanical Specifications Dimensions in inches (mm) Standard Rotary MAX Encoder/Control Knob LMAX2 Stack in (mm) Stack in (mm) 1713 2.187 (55.56) 1713 2.744 (69.71) 1715 2.407 (61.15) 1715 2.965 (75.30) 1719 2.786 (70.77) 1719 3.343 (84.92) Differential EncodeMAX2 1713
in „Alter Stepper-Treiber über ISP an USB parametrieren“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Diff_Ampl_AD8476-877860.pdf
= 25°C, unless otherwise noted. Table 1. BGrade A Grade Parameter TestConditions/Comments Min Typ Max Min Typ Max Unit DYNAMIC PERFORMANCE −3 dB Small Signal Bandwidth VOUT= 200 mV p-p 6 6 MHz −3 dB Large Signal Bandwidth VOUT= 2 V p-p 1 1 MHz Slew Rate V = 2 V step 10 10 V/µs OUT Settling Time to 0.01%
in „5V Differentielles Signal erzeugen“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
BLE112_Datasheet.pdf
operating conditions. The maximum recommended operating conditions are in the table 5. Rating Min Max Unit Storage Temperature -40 85 °C AVDD,DVDD, VDD_USB -0.3 3.9 V Other Terminal Voltages VSS-0.4 VDD+0.4 V Table 4: Absolute Maximum Ratings 3.2 Recommended Operating Conditions Rating Min Max Unit
in „BLE112 wer kennt sich mit dem UART aus ?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
apem_08162017_16300-1158414.pdf
Storage temperature Min. -65⁰C Max. +160⁰C Soldering IEC 68-2-20 Wave – max 260⁰C for max. 10 sec., please refer to usage guidelines Soldering iron – max. 350⁰C for max. 3 sec. Flux tight. Environmental Endurance IEC 68-2-3 Temperature
in „Suche Einbautaster mit 2 Leuchtanzeigen“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
T6963C.pdf
character generator ROM (code 0101) T6963C−0101 is built in as standard. ▯External display memory : 64 KB Max The addresses in display memory of the text area, graphic area and external character generator area are determined by software. ▯Read or Write operations from the CPU do not disturb the display. 000707EBA1
in „[V] Grafikdisplay 240x128“ · Markt ·
-
PDF
T6963C.pdf
character generator ROM (code 0101) T6963C−0101 is built in as standard. ▯External display memory : 64 KB Max The addresses in display memory of the text area, graphic area and external character generator area are determined by software. ▯Read or Write operations from the CPU do not disturb the display. ▯A
in „altes Phytec MCB-51 Monitor/Basic Befehle?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
linkswitch-hp_family_datasheet-844868.pdf
www.power.com Rev. E 06/15 LinkSwitch-HP Conditions Parameter Symbol SOURCE = 0 V; T = -40 to 125 °C Min Typ Max Units (Unless Otherwise Specified) Circuit Protection (cont.) Minimum Switch tLEB(MAX)ILD(MAX) ON-Time TON(MIN) 325 400 500 ns TJ= +25 °C Output T = +25 °C 6.9 7.97 LNK6xx3 J D = 100 mA T = +100 °C
in „Fujitsu B27T-7 TFT Monitor Netzteil defekt Bauteil 715G6503-P01-001-0010“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
XC6216_XE6216.pdf
OUT20mA OUT20mA OUT100mA OUT100mA VOLTAGE(V) VOUT(T) ΔVOUT ΔV OUT Vdif1 Vdif1 Vdif2 Vdif2 (V) TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. 2.0 450 600 450 735 1900 2600 1900 3060 2.1 2.2 2.3 390 520 390 675 1700 2200 1700 2760 2.4 2.5 2.6 2.7 310 450 310 620 1500 1900 1500 2620 2.8 2.9
in „Suche schaltung für Ladeerhaltung einer Pufferbatterie“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
AV02-0923EN-DS-ATF-55143-08Jun20120.pdf
100 DS I Gate Current [5] mA 1 GS P Total Power Dissipation [3] mW 270 diss P RF Input Power [5] in max. (Vds=2.7V, Ids=10mA) dBm 10 (Vds=0V, Ids=0mA) dBm 10 T ChannelTemperature °C 150 CH T StorageTemperature °C -65 to 150 STG Thermal Resistance [4] °C/W 235 jc ESD (Human Body Model) V 200 ESD (Machine
in „LNA Entwicklung von 10 MHZ bis 6 GHZ“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
IS2200E_V1.61.pdf
185 O51 3822.00 487.05 A 256 DUMMY 130.00 487.05 A 186 O52 3770.00 487.05 A 257 DUMMY 78.00 487.05 A 187 O53 3718.00 487.05 A 258 DUMMY 26.00 487.05 A 188 O54 3666.00 487.05 A 259 DUMMY -26.00 487.05 A 189 O55 3614.00 487.05 A 260 DUMMY -78.00 487.05 A 190 O56 3562.00 487.05 A 261 DUMMY -130.00 487.05
in „LCD-Modul OPTREX 351570AG“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
LT1083_LT1084_LT1085_LT.pdf
> 40°C/W DEPENDING ON MOUNTING TECHNIQUE. ELECTRICAL CHARACTERISTICS PARAMETER CONDITIONS MIN TYP MAX UNITS Reference Voltage I = 10mA, T = 25°C, OUT J (VIN– VOUT ) = 3V 1.238 1.250 1.262 V 10mA ≤I OUT≤ IFULL LOAD 1.5V ≤(V IN OUT) ≤25V (Notes 3, 5, 6) 1.225 1.250 1.270 V Line Regulation I = 10mA, 1.5V
in „Aus 12V 5V machen“ · Mikrocontroller und Digitale Elektronik ·