-
PDF
EWARM_DevelopmentGuide.ENU.pdf
return to the caller, by jumping to the address pointed to by the LR.ister At function entry, non-scratch registersLRnregister can be pushed with one instruction. At function exit, all these registers can be popped with one instruction. The return address can be popped directly
in „Viele Flags effizient speichern und schreiben/Byte in Bitfeld?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
PCA9626.pdf
from 0 % to 99.6 % that is used to either dim or blink all LEDs with the same value. Each LED output can be off, on (no PWM control), set at its individual PWM controller value or at both individual and group PWM controller values. The PCA9626 operates with a supply voltage range of 2.3 V to 5.5 V and
in „Probleme mit PCA9626 und I2C“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
slaa123.pdf
interrupt vectors and must not be modified during run time. Two more segments called Segment A and B each 128 bytes wide are allocated as information memory in the device. The user can use this information memory for storing device identification codes. The information memory can also be used to substitute
in „Nur ein einfacher Gong“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
M220SP01_V.0.pdf
Module may be damaged. press at the far 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT MRdule. 11)After installation of the TFTTModule into an enclosure
in „[S] TFT Steuerplatinen“ · Markt ·
-
PDF
steuerzeichen.pdf
DLE data link escapeSteuerung der 09232 0x2410 e2 90 90 SYMBOL FOR RIGHT-POINTING Verbindung DATA LINK TRIANGE ESCAPE 017 0x11 ctrl Q 09664 0x25c0 e2 97 80 BLACK DC1 device control #1 Steuerung der Einheit 1 09233 0x2411 e2 90 91 SYMBOL FOR LEFT-POINTING
in „konsolenanwendung zeilenumbruch zeile hoch“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
IS2200E_V1.61.pdf
5805.30 -523.35 B 127 TESTACS1 5929.70 -523.35 B 59 VDD2 -1258.25 -523.35 C 60 VDD2 -1153.75 -523.35 B 128 DUMMY 6029.90 -523.35 B 61 C1+ -1073.75 -523.35 B 129 DUMMY 6109.90 -523.35 B 62 C1+ -993.75 -523.35 C 130 DUMMY 6189.90 -523.35 B 63 C1+ -913.75 -523.35 B 131 DUMMY 6269.90 -523.35 B 64 C1- -755.05
in „LCD-Modul OPTREX 351570AG“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
DS_K4B8G1646Q-MY_Rev10.pdf
Command and Address(1.35V) DDR3L-800/1066/1333/1600 Symbol Parameter Unit NOTE Min. Max. 1.35V V (DC90) DC input logic high V + 90 V mV 1 IH.CA REF DD V (DC90) DC input logic low V V - 90 mV 1 IL.CA SS REF V (AC160) AC input logic high V + 160 Note 2 mV 1,2,5 IH.CA REF V (AC160) AC input logic low Note
in „Orange Pi - 15$ Quadcore SBC“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
sniu023.pdf
CRCW060333K0FKEA 0.1W, 0603 R41 1 1.00k RES, 1.00 k, 0.01%, 0603 RNCF0603TKY1K00 0.063 W, 0603 R50 90.9k RES, 90.9k ohm, 1%, 0603 RC0603FR-0790K9L 1 0.1W, 0603 R51 100k RES, 100k ohm, 1%, 0603 RC0603FR-07100KL 1 0.1W, 0603 R53, R55, R79 3 330 RES, 330 ohm, 5%, 0603 CRCW0603330RJNEA 0.1W, 0603 R62, R63
in „Ultraschallwandler ansteuern“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
AM700_SM.pdf
After you finish the touch screen calibration procedure, the screen displays the paint screen. You can touch the screen at various points and the screen will highlight where touched. You can use this screen to check any suspected inoperative locations on the touch screen. 6. When the calibration has
in „Tektronix AM700“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
Z80-Zilog.pdf
Registers Two matched sets of general-purpose registers, each set containing six 8-bit registers, can be used individually as 8-bit registers or as 16-bit register pairs. One set is called BC, DE, and HL while the complementary set is called BC', DE', and HL'. At any one time, the pro- grammer can select
in „DDR Schach-Computer Chess Master Diamond reparieren (Dauerton)“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
_Elmos__981_03.pdf
temperature TJ -45 150 °C Storage temperature TS -45 150 °C ESD immunity (human body model, this test can be ap- plied between any two pins of the IC) VESD,hbm -2 2 kV Voltage at digital and analog VIO pins: RESET, SAVE, XTAL, INT, SETVCC, OTEMP, SCS, SCK, MOSI, V -0.3 V VIO 0.3 V MISO, RXD, TXD, BS0, BS1
in „Exposed Pad anschließen? (ATSAMD20E18A-MU und ELMOS E981.03)“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
MFRC522.pdf
to 0101b for all MFRC522 devices. The remaining 3 bits (ADR_0, ADR_1, ADR_2) of the slave address can be freely configured by the customer to prevent collisions with other I2C-bus devices. If pin EA is set HIGH, ADR_0 to ADR_5 can be completely specified at the external pins according to Table 5 on
in „Schlüsselcodes in EEPROM identifizieren“ · Fahrzeugelektronik ·
-
PDF
Datasheet_MFRC522.pdf
to 0101b for all MFRC522 devices. The remaining 3 bits (ADR_0, ADR_1, ADR_2) of the slave address can be freely configured by the customer to prevent collisions with other I2C-bus devices. If pin EA is set HIGH, ADR_0 to ADR_5 can be completely specified at the external pins according to Table 5 on
in „IRQ am RFID RC522“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
LCMXO640C-3TN144C.pdf
accomplished through the programming interface during configuration. PFU Modes of Operation Slices can be combined within a PFU to form larger functions. Table 2-4 tabulates these modes and documents the functionality possible at the PFU level. Table 2-4. PFU Modes of Operation Logic Ripple RAM ROM LUT
in „Erfahrung mit Siglent SDG 10xx Arbitrary Generatoren?“ · Markt ·
-
PDF
lt1153.pdf
Current Limited Power Supplies drainsenseresistorexceedsabout0.7V,providingadirect The LTC1153 requires at least 3.5V at the supply pin to path to the sense pin and dramatically reducing the trip ensureproperoperation.Itisthereforenecessarythatthe delay time. The drain sense resistor value is selected to
in „TPS61175 Overccurent Protection Mode“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
Driver_Library_user_guide.pdf
a limit of at least 96 CAN_STATUS_EPASS - CAN controller is in the error passive state CAN_STATUS_RXOK - a message was received successfully (independent of any mes- sage filtering). CAN_STATUS_TXOK - a message was
in „I2C Display Steuern“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
main.c
/29 12:16:41 peter Exp $ Software: AVR-GCC 3.3 Target: any AVR device, memory mapped mode only for AT90S4414/8515/Mega DESCRIPTION Basic routines for interfacing a HD44780U-based text lcd display Originally based on Volker Oth's lcd library, changed lcd_init(), added additional constants for lcd_command
in „Alles schwarz nach Initial. bei Display (4x20, KS0076B)“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
W2000US_Data_Sheet.pdf
Vertically expand or compress a live or stopped waveform Max Input Voltage 300 VRMS CAT II Position Range at 2mV/div to 200mV/div ± 2V; at >200mV/div to 5V/div ± 50V BW Limit 20MHz Input Coupling AC, DC, GND Input Impedance 1MΩ parallel with 15pF Time Base Range 5ns to 50sec/div Time Base Accuracy 50ppm Horizontal
-
PDF
datenblatt_pic.pdf
of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character
in „Flußdiagramm Digitale stoppuhr auf PIC 16F84A“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
16F84.pdf
of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character
in „Probleme mit Taktversorgung auf Steckbrett“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
KS0093.pdf
when data are written/read in succession, the address is automatically increased by 1. The 5 icons at a time can blink, if C and B bits of the display instructions are enabled. The blink attributes of ICON are same as the cursor blink. For accessing DD/CGRAM, the DD/CGRAM Address Set instruction should
in „LCD seriell ansteuern ST7093/KS0093“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
magnetic.pdf
.) can be calculated by using the potentials at the postprocessing stage. Capacitance, inductance, energy, force and other quantities can also be calculated. The postprocessing give a chance to modify the
-
PDF
Alto_D1__D2__D3__D4_Power_Amp_Service_Manual.pdf
power-on, signal, clip and protection. Standard power connectors are used for power outputs. Input can be parallel or stereo or bridge and an high quality audio transformer can be added on the input stage of each channel. It provides the following features: 2U rack, multi-channel high power amplifier
in „Endstufe reparieren, Bauteil identifizieren“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
SPACE_VECTOR_MODULATION_AND_CONTROL.pdf
and usable gates as well as the number of I/O pins that can be configured. This limits the maximum size of the logic circuitry that can be implemented with any given EPLD. At the time of the board development two, FLEX 8820 chips from ALTERA looked like a very
in „Literatur für Raumzeigermodulation“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
RFM22B.pdf
in each packet. A CRC is computed and appended at the end of each transmitted packet and verified by the receiver to confirm that no errors have occurred. The packet handler and CRC can significantly reduce the load on the system microcontroller allowing
-
PDF
RFM22B.pdf
in each packet. A CRC is computed and appended at the end of each transmitted packet and verified by the receiver to confirm that no errors have occurred. The packet handler and CRC can significantly reduce the load on the system microcontroller allowing
-
PDF
tmp275.pdf
0000 0000 000 Temperature −0.25 1111 1111 1100 FFC TLOW −25 1110 0111 0000 E70 −55 1100 1001 0000 C90 Table 5. Temperature Data Format TMP275 ALERT PIN (Comparator Mode) The user can obtain 9, 10, 11, or 12 bits of resolution by POL = 0 addressing the Configuration Register and setting the TMP275 ALERT
in „Abmessungen Datenblatt“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
self-res.pdf
radio filter applic17ions; which implies that the wave is intimately associated with the guiding wire, at least at the SRF . More information about the nature of the travelling wave can be had by using dipoles for both source and receiver; with cables brought straight-out at the back and choked-off with
-
PDF
en.CD00254735.pdf
is then fixed at the maximum value of 1 V. If a lower setpoint is desired to reduce the power dissipation on Rs, the pin can be also biased at a fixed voltage using a divider from VREF (pin 10). If the FF option is selected
in „Flybackcontroller“ · Analoge Elektronik und Schaltungstechnik ·
-
PDF
EjN-ST-A10_LIUST-5X_CustomerDisplay.pdf
can be executed at the same time. (Smooth scrolling is avaible.) 2.1.9. All lines horizontal scroll (Valid only for LIUST-52/LIUST-53) (Specified maximum characters are 128 (64 for full size characters) Smooth scroll by dots. Specifying multiple lines is allowed. The speed of scrolling can be specified. (10ms/dot 20ms/dot) Other commands can not be executed at the same time. (Smooth scrolling is avaible.) 2.5 TEC Corporation EYA03969 2.2. Host interface 2.2.1. Interface Communication
in „Hat schon jemand was mit dem FUJITSU VF60 Display gemacht?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
EjN-ST-A10_LIUST-5X_CustomerDisplay.pdf
can be executed at the same time. (Smooth scrolling is avaible.) 2.1.9. All lines horizontal scroll (Valid only for LIUST-52/LIUST-53) (Specified maximum characters are 128 (64 for full size characters) Smooth scroll by dots. Specifying multiple lines is allowed. The speed of scrolling can be specified. (10ms/dot 20ms/dot) Other commands can not be executed at the same time. (Smooth scrolling is avaible.) 2.5 TEC Corporation EYA03969 2.2. Host interface 2.2.1. Interface Communication
in „Hat schon jemand was mit dem FUJITSU VF60 Display gemacht?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
SMB380_Preliminary_Datasheet_Rev13_20070918.pdf
bit 7) is at 1, the any_motion criterion will set SMB380 into alert mode (section 3.2.9). This bit can be masked by enable_adv_INT, the value of this bit is ignored when enable_adv_INT=0 (section 3.2.3). Rev. 1.3
in „Problem SMB380“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
4620.pdf
of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character
in „SPI master/slave - schreib/lese befehle ?“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ssd1803a.pdf
several bytes continuously without changing RS bit and RW bit, start byte transfer is needed only at first starting time. Namely, after first start byte is transferred, real data can be transferred succeeding. Read Operation (R/W = 1) After start byte is transferred to SSD1803A, MPU can receive 8-bit
in „Probleme mit EADOGM204-4 und ATMEGA32“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ssd1803a_2_0.pdf
several bytes continuously without changing RS bit and RW bit, start byte transfer is needed only at first starting time. Namely, after first start byte is transferred, real data can be transferred succeeding. Read Operation (R/W = 1) After start byte is transferred to SSD1803A, MPU can receive 8-bit
in „Display DOGM-204A/SSD1803A mit I2C - ROM Auswahl“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
ffft.S
of points FFT_N is defined in "ffft.h" and the value can be ; power of 2 in range of 64 - 1024. ; ;----------------------------------------------------------------------------; ; 16bit fixed-point FFT performance with MegaAVRs ; (Running at 16MHz/internal
in „AVR Assembler Konstanten variabel machen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
BMA020_DataSheet_1.1_080114.pdf
7) is at 1, the any_motion criterion will set BMA020 into alert mode (section 3.2.9). This bit can be masked by enable_adv_INT, the value of this bit is ignored when enable_adv_INT=0 (section 3.2.3). Rev. 1.1
in „Über Mikrocontroller Beschleunigungssensor auslesen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
BMA020_DataSheet_1.1_080114.pdf
7) is at 1, the any_motion criterion will set BMA020 into alert mode (section 3.2.9). This bit can be masked by enable_adv_INT, the value of this bit is ignored when enable_adv_INT=0 (section 3.2.3). Rev. 1.1
in „Bosch BMA020 Zweierkomplement“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
90000897.pdf
most out of their Digi product. For information on TechnicalSupport plans and pricing, contact us at +1 952.912.3444 or visit us at www.digi.com/support. Digi Connect ME, Wi-ME, ME 9210, Wi-ME 9210HardwareReferenceManual 3 Contents About this document Scope of the reference manual 7 Relateddocumentation
in „[V] WEITERE gebrauchte DIGI-Connect-ME LAN-Seriell Module (10€/St.)“ · Markt ·
-
PDF
02-ETEK-Modular-Distribution-Electric-2024.pdf
Box With Neutral and Earth Terminal Dimension(mm) Model Ways H W D D1 W1 H1 EKDB16-6 6 259 162 114.5 90 156 255 EKDB16-10 10 259 234 114.5 90 225 255 EKDB16-14 14 259 306 114.5 90 300 255 EKDB16-18 18 259 378 114.5 90 372 255 EKDB16-24 24 259 486 114.5 90 480 255 EKDB16-28 2x14 509 306 114.5 90 300 505
in „Balkonkraftwerk an alter E-Installation“ · Haus & Smart Home ·
-
PDF
B1nn.pdf
For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com. © 2009 Microchip Technology Inc. DS21711J-page 3 24AA01/24LC01B FIGURE 1-1: BUS TIMING DATA 5 4 2 3 SCL 7 8 9 10 6 SDA IN 14 11 12 SDA OUT
in „IPL Lampe Blitzcounter rücksetzten“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
PCF7922ATT.pdf
1FH SN 1 PI SN 0 complete byte. Up to four bytes may be subject to an Page 0 ERASE/WRITE operation at the same time. bit 31 8 7 4 3 bit 0 MSB LSB 10.1.1 Organisation 18H 19H1A HB H The 512 byte of non-volatile memory (EEPROM) are 1 0 0 0 PI organized as 128 pages, each page assembled by four byte with
-
PDF
Schaltplan_FARBE.pdf
PB7 137 PB6/I2C1_SCL/TIM4_CH1 PF4/FSMC_A4 15 PF5 A4 SDIO_D0 PC8 7 D1 PE12 51 52 PE11 PD9 51 52 PD8 CAN_RX PB8 139 PB7/I2C1_SDA/FSMC_NADV/TIM4_CH2 PF5/FSMC_A5 18 PF6 A5 LED1 6 D0 53 54 53 54 CAN_RX PB8/TIM4_CH3/SDIO_D4 PF6/ADC3_IN4/FSMC_NIORD GND PE14 55 56 PE13 PB15 55 56 PB14 CAN_TX CAN_TX PB9 140 PB9
in „STM32 Port-Initialisierung“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
esp32-c3_technical_reference_manual_en.pdf
by setting GPIO_FUNCx_OUT_INV_SEL bit. 5.5.3 Simple GPIO Output GPIO matrix can also be used for simple GPIO output. This can be done as below: • Set GPIO matrix GPIO_FUNCn_OUT_SEL with a special peripheral index 128 (0x80); • Set the corresponding bit in GPIO_OUT_REG register
in „Mit dem ESP32C3 laufen lernen“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
esp32-c3_technical_reference_manual_en.pdf
by setting GPIO_FUNCx_OUT_INV_SEL bit. 5.5.3 Simple GPIO Output GPIO matrix can also be used for simple GPIO output. This can be done as below: • Set GPIO matrix GPIO_FUNCn_OUT_SEL with a special peripheral index 128 (0x80); • Set the corresponding bit in GPIO_OUT_REG register
in „ESP32C3 > PLL“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
PIC18f6622.pdf
data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character
in „PIC 18F6622 Zeit um EEPROM zu schreiben“ · Mikrocontroller und Digitale Elektronik ·
-
Datei
AT89C51ED2.h
__sfr __at (0x89) TMOD ; __sfr __at (0x8A) TL0 ; __sfr __at (0x8B) TL1 ; __sfr __at (0x8C) TH0 ; __sfr __at (0x8D) TH1 ; __sfr __at (0x90) P1 ; __sfr __at (0x98) SCON ; __sfr __at (0x99) SBUF ; __sfr __at (0xA0
in „Include Datei AT89C51ed2“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
20120224183241077.pdf
management system for gate driver and source driver. and reduce data transfer − Moving and still picture can display at the same time The built-in timing controller in OTM4001A can support several − Vertical scrolling function interfaces for the diverse request of medium or small size portable − Partial screen
in „Handydummy (Attrappe)mit richtigem Display - Sony Ericsson Vivaz“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
ADG714_715.pdf
dBtyp RL=50Ω, C =LpF, f =1MHz Channel-to-Channel Crosstalk –70 dB typ R =50Ω, C =5pF, f =10MHz L L –90 dBtyp RL=50Ω, C =LpF, f =1MHz –3 dB Bandwidth 155 MHz typ RL=50 Ω, C =LpF C S(OFF) 11 pF typ C DOFF) 11 pF typ C , C (ON) 22 pF typ D S POWER REQUIREMENTS VDD = 5.5 V I 10 μA typ Digital Inputs = 0 V
in „Arduino Uno & ADG714 via SPI funktioniert nur sporadisch“ · Mikrocontroller und Digitale Elektronik ·
-
PDF
MASM61PROGUIDE.pdf
(The overflow flag is also set if both operands are negative and the sum is less than or equal to -128.) Placing a JO (Jump on Overflow) or INTO (Interrupt on Overflow) instruction in your program at this point can transfer control to error-recovery statements. When the sum exceeds 255, the processor sets the carry flag. A JC (Jump on Carry) instruction at this point can transfer control to error-recovery statements. In the previous subtraction example, the processor sets the sign flag if the result goes below 0. At this point, you can use a JS (Jump on
in „SumArray Proc Uses SI, Was heisst bitte das Uses bei MASM?“ · Softwareentwicklung ·